Correct Replacement for TDE 46210 Trailer Hub

Question

Question:

I dont see a number on the spindle. It looks like the #85. Should it be stamped somewhere?

asked by: Tim M

0

Expert Reply:

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500 lb axle so you can use the Trailer Idler Hub Assembly part # AKIHUB-545-35-G-EZ-K for galvanized or part # AKIHUB-545-35-K for standard.

expert reply by: Conner L

0

Frank

3/13/2025

incorrect information the standard 5 on 4.5 hub for a 84 spindle will not replace this hub when brakes are in the equation.. FYI

Jameson C.

3/13/2025

@Frank Because of the lack of a drum?

Answer 1

Hey Patrick, thanks for reaching out. Yes, the Replacement Front Jack Leg #LC362485 should work for your 2021 Open Range 314RLS with the Lippert Ground Control 3.0 system. Since your weld stop “bump outs” measure 17-1/2" apart, that matches the…

view full answer...

Answer 2

Hey Eddie, thanks for the pictures. From seeing that I can tell you have a 3,500 lb axle and the correct replacement hub would be the part #AKIHUB-545-35-G-EZ-K that you referenced which comes with new bearings and seal.

view full answer...

Answer 3

Hey Frank, I looked up that rotor and it looks like it's a 10" rotor with a 5 on 4 1/2 bolt pattern. That being said, you can use the Kodiak 10" Hub-and-Rotor Assembly #KHR10D as a replacement, with the Grease Seal #RG06-050, the Timken…

view full answer...

Answer 4

Hey Steve, you are correct the only grease cap solution we have for a diameter of 2.047 inches is a Bearing Buddy with the part #BB2047. We do not have a standard grease cap in this size.

view full answer...

Answer 5

Jeff, I believe that is an older TDE hub which would mean that the Trailer Idler Hub Assembly for 3,500-lb Axles #AKIHUB-545-35-K is the correct replacement.

view full answer...

Answer 6

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information as we don't have a way to pull up what your trailer would have. The first thing you will need to know is the bolt pattern of…

view full answer...

Answer 7

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

Answer 8

We have just what you are looking for. I called my contact at TDE and asked about the hub you have on your boat trailer. They told me that it was a 5-stud idler hub for a 3,500-lb axle. That means you need the part #AKIHUB-545-35-K. This is a fit for…

view full answer...

Answer 9

The 171255UC seal is the same as the Dexter 010-11088/K71-G01-80. We have that same seal available as the Grease Seal Kit- Triple Lip - Inner Diameter 1.719" - Outer Diameter: 2.565" - Qty 2 #DX49CR.

view full answer...

Answer 10

Hey Jeff! The Replacement Head for Reese Weight Distribution System item #RP58167 you were looking at is our only option for trunnion bars. It works with Trunnion Spring Bars like item #RP22225. The head will have the capacity of whatever bars you…

view full answer...

Answer 11

Overpacking the trailer hub with grease is the number one reason for grease seal failure. For a boat trailer I would recommend re-packing the hubs by hand with grease once per season and you'd be fine. I don't like recommending people use…

view full answer...

Answer 12

The Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-1/2 - Galvanized #AKIHUB-545-35-G-EZ-K you were looking at includes Grease Seal #58846 which is indeed a double lip seal. This seal has an I.D. of 1.719" and an O.D. of…

view full answer...

Correct Replacement for TDE 46210 Trailer Hub

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching