Axle Replacement For Tracker Trailstar Trailer

Question

Question:

Hi - I have a 2003 Tandem Axle Tracker Trailstar trailer and I am trying to find a replacement axle. The dimensions are the following 84inch Hub distance, 72inch Spring distance, and 89inch overall distance.

asked by: Daniel B

0

Expert Reply:

It sounds like you have a different size axle than anything we carry. The closest we have is the Dexter Trailer Axle w/ Electric Brakes - E-Z Lube - 6 on 5-1/2 Bolt Pattern - 86-1/2" - 5.2K # 8327816-EB which has spring centers at 71-1/2 inches on center. This is a larger capacity than the 3500 lb system you asked from, but is a better fit with your measurements.

If that won't work for you, then I recommend the universal Timbren Axle-Less system that has the integrated suspension. These mount directly to the frame and require a 2 inch square tube between the assemblies at the integrated holes. I recommend the # A35RS545E for 3,500 lb capacity.

expert reply by: Jason S

0

Buzz F.

7/14/2024

I am looking for a trailstar trailer axle. The Vin # is 4tm12sf19bb001177

Kyle S.

7/15/2024

@BuzzF So unfortunately we can't do anything with a VIN, as there's no sort of database that online retailers have special access to in order to look up parts. I'll go ahead and link a video below which shows you how to measure to pick the right axle, and also our selection of axles.

Helpful Links

dept-pg-trailer_axles-sf-leaf_spring_suspension.aspx

tv-faq-how-to-measure-and-choose-the-right-trailer-axle.aspx

Greg S.

5/25/2025

1992 tracker trailstar need new axle believe 2000 lb i need to remeasure from hub to hub ruffly measured 72 1/2 inches end to end ..can you help thanks

Jameson C.

5/27/2025

@GregS We have the part # e32GR which is a 2k rated axle that is 72 inches long. The spring seat center to center dimension is 58 inches so you'll need to verify that is the same as what you have as well. This is currently the only option we have that matches capacity and overall length though.

Answer 1

The 10" x 1-1/2" braking assemblies part #K23-472-473-00 will use the same four bolt brake mounting flange as the 10" x 1-3/4" braking assemblies you have but the hub/drum that goes with these uses a LM67048 inner bearing and…

view full answer...

Answer 2

Hey Glenn, thanks for all of the info on your current hub. From that we know that you have a 2,200 lb axle and the correct hub replacement would be the part #8-258-5UC1-EZ. This is also pre-greased so it's ready to be installed on your trailer.…

view full answer...

Answer 3

The UFP hub that you've referenced isn't made any longer I don't believe, but we do have some options for you. From some previous customers, we've determined that the UFP H-1062-3 axle has a spindle that has #L44649 inner and outer…

view full answer...

Answer 4

It might be Dan but I wasn't able to pull any specific information off of the UFP 13674 part number you gave me. What you'll need to do is pull one of the hubs and read the part numbers stamped into the sides of the bearings. This information…

view full answer...

Answer 5

That would be the depth of the inside of the hub. If you check out the picture I attached the blue lines represent the depth. This will also be the width of the brake shoes on the brake assemblies. I attached a review video for this hub for you to…

view full answer...

Answer 6

I attached a link to the right that contains detailed installation instructions for the Titan Zinc-Plated Brake Actuator #T43397007K that you can use as a guide to install this coupler on your 1994 Maxum 20 foot boat trailer.

view full answer...

Answer 7

I may have a solution for you, however we do not have a standard axle available that matches the dimensions on your current unit. I recommend taking a look at a Timbren Axle-Less System to replace the axle on your Trailstar Bass Tracker Trailer. This…

view full answer...

Answer 8

Some trailers are equipped with EZ Lube spindles, which have a grease fitting or zerk in the end of the spindle, and a small hole in the spindle that lets grease enter the interior of the hub and reach the bearings. This allows grease to be added to…

view full answer...

Answer 9

Hey Brad, to replace your Tie Down Engineering LP70 actuator, I recommend going with the Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-20. This actuator will fit on 3" wide channel tongues, will work with 2" balls, and has a 7,500 lb…

view full answer...

Answer 10

Hey Mike congrats on the new truck! The only reusable part of your Curt A20 5th Wheel Trailer Hitch for Ram Towing Prep Package item #C16044 is the actual hitch head itself. The adapter bracket with legs that attaches to the puck system is not…

view full answer...

Answer 11

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 12

From what I was able to find out from my research, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles. Replacement hubs that have these specs typically use a #L68149 inner bearing and #L44649…

view full answer...

Axle Replacement For Tracker Trailstar Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching