Installation Instructions for the Titan Zinc-Plated Brake Actuator # T43397007K

Question

Question:

Trying to install it on a boat trailer for a 1994 Maxum 20 foot boat. Installation instructions?

asked by: Steve W

0

Expert Reply:

I attached a link to the right that contains detailed installation instructions for the Titan Zinc-Plated Brake Actuator # T43397007K that you can use as a guide to install this coupler on your 1994 Maxum 20 foot boat trailer.

expert reply by: Jameson C

0

Answer 1

That would be the depth of the inside of the hub. If you check out the picture I attached the blue lines represent the depth. This will also be the width of the brake shoes on the brake assemblies. I attached a review video for this hub for you to…

view full answer...

Answer 2

I may have a solution for you, however we do not have a standard axle available that matches the dimensions on your current unit. I recommend taking a look at a Timbren Axle-Less System to replace the axle on your Trailstar Bass Tracker Trailer. This…

view full answer...

Answer 3

It sounds like you have a different size axle than anything we carry. The closest we have is the Dexter Trailer Axle w/ Electric Brakes - E-Z Lube - 6 on 5-1/2 Bolt Pattern - 86-1/2" - 5.2K #8327816-EB which has spring centers at 71-1/2 inches…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Installation Instructions for the Titan Zinc-Plated Brake Actuator # T43397007K

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching