How does the Optronics LED Identification Light # MCL98RB Mount

Question

Question:

how does this lamp mount?

asked by: James

0

Expert Reply:

The Optronics LED Identification Light, # MCL98RB, is a surface mount light that has two holes for mounting screws. The mounting holes measure 3/16 inch x 3/8 inch and are 8-1/2 inches apart on center. I have attached a photo showing the dimensions for you.

The mounting hardware is not included with the light, but any local hardware store will carry the necessary screws.

expert reply by: John H

0

click to enlarge

Answer 1

Actually yes I can help, check out the video I attached that shows exactly how to install this LED Identification Light #MCL98RB on a trailer.

view full answer...

Answer 2

Water and electricity don't mix well. The best recommendation I can make for you would be to unplug your trailer wiring before you back your boat trailer down the ramp and then don't plug the lights back in until the trailer has dried out…

view full answer...

Answer 3

The LED Identification Light Bar for Trailers over 80" Wide - Submersible - 9 Diodes - Red Lens #MCL93RB has the wiring and housing for the individual sealed lights #AL91RB to fit. The only way to help them stay in place a little better is to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How does the Optronics LED Identification Light # MCL98RB Mount

Product Page this Question was Asked From

Continue Researching