Replacement Motor for Lippert Electric Coach Steps 725-0022

Question

Question:

2005 Holiday Rambler 40 PDQ Endeavor What step motor and linkage do I need ? The information Ive found on the Coach Step to be replaced is: SN 1686833 Part # 725-0022 Step Assy Its a 2 step

asked by: Ed S

0

Expert Reply:

The Lippert Electric Coach Steps all use the Replacement Motor part # LC301695. In regards to the linkage, it sounds like you might be looking for the Replacement Double Ball Joint part # LC388220 but if not just let me know.

expert reply by: Conner L

0

Answer 1

I have a complete replacement camera system option for you, but unfortunately your current VCCS130B camera has been discontinued and there is no compatible camera still made. While it's not what you're hoping to hear, I recommend replacing…

view full answer...

Answer 2

Based on my research, it looks like the part 725-0021 is a single step electric Coachstep, and we do have the correct replacement motor, which is the following part: - Replacement Motor for Lippert Electric Coachstep #LC301695 I verified with the…

view full answer...

Answer 3

I sent all of the pictures you sent me to the current manufacturer of the Coach steps (Lippert) and they told me that the correct module you need is the part #LC301702. Your wire colors might not totally match but the purple wire of the new module is…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Motor for Lippert Electric Coach Steps 725-0022

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching