How to Determine if Wheel Trailer Setup is Hub-Centric or Lug-Centric
Updated 06/30/2020 | Published 06/26/2020
Products Featured in This Question
Question:
Are my trailer wheels hub centric or lug centric? The hole in the wheel does not appear to butt up against the hub. Looks like a pretty good gap there. I have taken a couple of close up pictures that I have attached. I can also stick a tape measure against the hub and there is a 1/4 gap to the edge of the wheel hole. I miked the hole at 3.19, the hub at 2.67+-. The reason the question came up is because I have lug bolts instead of lug nuts. I am sorry to be such a pain... Thanks,
asked by: Michael P
Expert Reply:
Looks like you have a hub-centric setup because you secure your wheels using lug bolts like part # RG02-020 instead of lug nuts like part # CE11051. The whole hub-centric wheel vs lug-centric wheel can be a bit confusing but it's as simple as noting whether you use bolts or nuts to secure your trailer wheel!
Product Page this Question was Asked From
Trailer Wheel Bolts - 1/2" Diameter x 1" Long - 60 Degree - Qty 4
- Accessories and Parts
- Boat Trailer Wheels
- Trailer Hubs and Drums
- Trailer Tires and Wheels
- Wheel Bolts
- 1/2 Inch Diameter
- Fine Thread
- 1 Inch Long
- Redline
more information >
Continue Researching
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Search Results: galvanized trailer fenders
- Shop: Bearing Kit for 1" BT8 Spindle, L44643 Inner/Outer Bearings, 34823 Seal
- Q&A: Are the Trailer Wheel Bolts RG02-020 Galvanized
- Q&A: Can Trailer Tire & Wheel Combo # AM35351DX be Used with Hub that Uses Wheel Bolts and Not Lug Nuts
- Q&A: How to Determine if a Trailer Wheel is Hub-Centric or Lug-Centric
- Q&A: Difference Between Trailer Hubs that are Lug Centric and Hub Centric
- Q&A: Using Hub Centric Rings on Trailer Wheels
- Shop: CE Smith Single Axle Trailer Fender - Pre-Galvanized Steel - 15" Wheels - Qty 1
- Shop: Single Axle Trailer Fender - Rounded Edges - Cold Rolled Steel - 8" to 12" Wheels - Qty 1
- Shop: Trailer Hub Grease Cap with Rubber Plug, 2.72" - Drive-In for EZ Lube Axles - Qty 1
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-3/4
- Shop: Trailer Wheel Bolts - 1/2" Diameter x 1" Long - 60 Degree - Qty 4
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Measuring To Choose The Right Trailer Axle
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Search Results: trailer jack
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Shop: Gooseneck Hitch
on Accessories and Parts
