Are the Trailer Wheel Bolts RG02-020 Galvanized

Question

Question:

RG02-020 Are these wheel bolts galvanized, or available as such? Or perhaps in stainless steel?

asked by: Chris B

0

Expert Reply:

I checked with my contact at Redneck and he confirmed that these Wheel Bolts # RG02-020 are zinc plated which is very similar to galvanization.

expert reply by: Jameson C

0

Answer 1

Looks like you have a hub-centric setup because you secure your wheels using lug bolts like part #RG02-020 instead of lug nuts like part #CE11051. The whole hub-centric wheel vs lug-centric wheel can be a bit confusing but it's as simple as…

view full answer...

Answer 2

First, I would say if there is any question on the road worthiness of the trailer, take the steps to correct it. Better safe than sorry. Some trailers have wheels that are hub-centric, the wheel is centered on the hub using the center pilot holes.…

view full answer...

Answer 3

It is easy to tell which type of wheel you have on your boat trailer. Lug centric wheels slide onto studs on the hub and are secured with lug nuts, like a car tire. If a wheel is hub centric, the wheel centers on the hub and bolts are threaded into…

view full answer...

Answer 4

A spacer or hub-centric ring is sometimes used on passenger vehicles, but our resident wheel and tire guru tells me that they aren't needed for use on trailers, due to the weight load a trailer wheel will be under. If you feel you need them, you…

view full answer...

Answer 5

Because your hubs take wheel bolts that means that the wheels are hub-centeric meaning it uses the hub to center the wheel. For this design the pilot hole of the wheel has to match exactly with the old wheels. On tire and wheel combo #AM35351DX the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Are the Trailer Wheel Bolts RG02-020 Galvanized

Product Page this Question was Asked From

Continue Researching