Does Draw Tite Hitch DT45519 Fit 2006 Chevy Silverado 3500

Question

Question:

I have a 2006 Chevy silvy3500 4x4 with a bed will it fit on my truck

asked by: Jeremy P

0

Expert Reply:

Yes, the Draw Tite hitch part # DT45519 is a confirmed fit for your 2006 Chevy Silverado 3500 long bed truck!

expert reply by: Jameson C

0

Answer 1

We haven't had the chance to install the Curt Class V Trailer Hitch Receiver #C15703 on the 2008 Chevy Silverado 2500 so I don't have exactly how far beneath the bumper the receiver will sit, however I did go out to our warehouse to take a…

view full answer...

Answer 2

Ground clearance is generally not a problem on full size trucks like your 2007 Chevy Silverado 3500. With that said the 2-1/2 inch hitches for the truck do hang fairly low. The Draw-Tite hitches #DT45519 and #DT45517 fit a little tighter to the rear…

view full answer...

Answer 3

I wouldn't say any of the 7-way trailer manufacturers that we sell offer a 7-way that is noticeably nicer than the other brands. I've heard people complain about Hopkins brake controllers and other more advanced electronics but I have a…

view full answer...

Answer 4

By mounting hole dimensions I assume you are asking about the distance between them, and that distance is 39 inches for the Draw-Tite Trailer Hitch Receiver #DT45519. That is the same distance between the mounting holes as the similar hitch from Curt…

view full answer...

Answer 5

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 6

Thanks for reaching out, Jon! To replace the factory hitch on your 2002 Chevy Silverado 3500 I recommend the Draw-Tite Ultra Frame Trailer Hitch Receiver #41944. For something a bit more heavy duty we have the Draw-Tite Trailer Hitch Receiver…

view full answer...

Answer 7

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 8

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 9

I would be happy to and thanks for the pictures! The B&W Heavy-Duty Trailer Hitch item #BWHDRH25122 measures 5.4" from the top of the frame brackets to the top of the receiver and 19-1/2" to the back of the receiver from the last bolt.…

view full answer...

Answer 10

As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver #C14082 is…

view full answer...

Answer 11

It looks like you're asking about the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25122, for your 1996 Ford F-150. You didn't say exactly which dimensions you're looking for but I went out to the warehouse and measured the…

view full answer...

Answer 12

In regards to the Curt Trailer Hitch Receivers for a 2001 Chevrolet Silverado 2500 HD - 6-1/2 Foot Bed, the part #C14108 will sit closer to the bumper like the factory hitch when compared to the part #14211. The latter has a higher class rating which…

view full answer...

Does Draw Tite Hitch DT45519 Fit 2006 Chevy Silverado 3500

Continue Researching