Are All Brands of 7-Ways Equal or Are There Better Options

Question

Question:

7 pin trailer plug. Are all the major brands like Reese Hopkins, etc , of equal quality? Or, is there a BEST brand for quality components and design? Thank you

asked by: Dr M

0

Expert Reply:

I wouldn't say any of the 7-way trailer manufacturers that we sell offer a 7-way that is noticeably nicer than the other brands. I've heard people complain about Hopkins brake controllers and other more advanced electronics but I have a Hopkins 7-way/4-way on my Tahoe part # HM40920 and it's been perfectly reliable and works great. This is a twist lock for GM vehicle bumpers. We also have a more standard fit part # HM40950 which fits the standard brackets.

expert reply by: Jameson C

0

Answer 1

Yes, the Draw Tite hitch part #DT45519 is a confirmed fit for your 2006 Chevy Silverado 3500 long bed truck!

view full answer...

Answer 2

We haven't had the chance to install the Curt Class V Trailer Hitch Receiver #C15703 on the 2008 Chevy Silverado 2500 so I don't have exactly how far beneath the bumper the receiver will sit, however I did go out to our warehouse to take a…

view full answer...

Answer 3

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 4

By mounting hole dimensions I assume you are asking about the distance between them, and that distance is 39 inches for the Draw-Tite Trailer Hitch Receiver #DT45519. That is the same distance between the mounting holes as the similar hitch from Curt…

view full answer...

Answer 5

Thanks for reaching out, Jon! To replace the factory hitch on your 2002 Chevy Silverado 3500 I recommend the Draw-Tite Ultra Frame Trailer Hitch Receiver #41944. For something a bit more heavy duty we have the Draw-Tite Trailer Hitch Receiver…

view full answer...

Answer 6

Ground clearance is generally not a problem on full size trucks like your 2007 Chevy Silverado 3500. With that said the 2-1/2 inch hitches for the truck do hang fairly low. The Draw-Tite hitches #DT45519 and #DT45517 fit a little tighter to the rear…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Are All Brands of 7-Ways Equal or Are There Better Options

Continue Researching