Recommended SnapPads for 2018 Winnebago Journey with PowerGear Jacks on 10-1/4" Diameter Feet

Question

Question:

Looking for SnapPad set for motorhome - from label on front jacks they are PowerGear. Front is image with ONE spring, Rear is image with TWO springs.

asked by: Ronald G

0

Expert Reply:

I have good news! I was able to reach out to my contacts at SnapPad and they tell me that the SnapPads # SP84FR4 you were looking at will fit on the 10-1/4" round concave feet of your 2018 Winnebago motorhome. The springs won't come into play since these fit directly onto the outside and bottom of the feet and will help provide a larger footprint to keep your landing gear from sinking into the ground.

expert reply by: Erik B

0

Answer 1

We've spoken with SnapPad about the correct SnapPad setup for your Winnebago Vista in the past and they have informed us that the correct kit is the part #SP84FR4 which matches diameter and foot shape you mentioned.

view full answer...

Answer 2

The SnapPad Jack Stand Pads for Motorhome part #SP84FR4 are designed for 10" Octagon foot plates. This kit includes the four you're looking for.

view full answer...

Answer 3

That's a good question and the difference between the two SnapPad Jack Stand Pads for Motorhome are different shapes and depths, it isn't solely the notch in the center. I added photos of the two pads side-by-side so you can see the…

view full answer...

Answer 4

There is no specific fit guide for jack feet so you'll need to measure your jack feet to know which size will fit your RV. For example if you have 10" jack feet you'll want the SnapPad Jack Pads for Class A and C Motorhome w/ 10"…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

Hey Ron, congratulations on the new trailer! I have a Jay Feather myself and love it. You're definitely off to a great start with a weight distribution hitch, it will make a world of difference towing that trailer with your F-150. The Weigh Safe…

view full answer...

Answer 9

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Recommended SnapPads for 2018 Winnebago Journey with PowerGear Jacks on 10-1/4" Diameter Feet

Product Page this Question was Asked From

Continue Researching