Dimensions from Receiver Opening to Mounting Brackets for Buyers Products 2" Hitch for GMC Van

Question

Question:

Can you tell me the height from the frame rail to the top of the actual 2x2 receiver hole? I have a deep step on a KUV cutaway. Just want to know before I order.

asked by: John

0

Expert Reply:

From where the mounting brackets on the Buyers Products 2" Hitch Receiver # 3371801102 will meet up to the frame of your GMC van down to the top of the receiver opening measures 7" (see attached).

expert reply by: Jon G

0

click to enlarge

Answer 1

The hole centers for the Buyers Products 2" Hitch Receiver #3371801102 are 39-1/4" from drivers side frame rail to passenger side frame rail. This receiver is confirmed to fit the 2014-2021 Chevrolet/GMC Express/Savana Cutaway Chassis. If…

view full answer...

Answer 2

On the Buyers Products hitch, part #3371801102, the mounting holes are 38-3/8 inches across center on center. Then on each side starting with the hole that's towards the rear of the vehicle they measure 3-11/16 inches from the first to the center…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Dimensions from Receiver Opening to Mounting Brackets for Buyers Products 2" Hitch for GMC Van

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching