Mounting Hole Dimensions of Buyers Products Trailer Hitch for GM Van Cutaway

Question

Question:

Can you tell me the mounting hole dimensions on this hitch? across and front to back?

asked by: Lisa

0

Expert Reply:

On the Buyers Products hitch, part # 3371801102, the mounting holes are 38-3/8 inches across center on center. Then on each side starting with the hole that's towards the rear of the vehicle they measure 3-11/16 inches from the first to the center hole and 6-7/16 inches from first to the last hole.

Take a look at the diagram I've attached.

expert reply by: Charles S

0

click to enlarge

Answer 1

The hole centers for the Buyers Products 2" Hitch Receiver #3371801102 are 39-1/4" from drivers side frame rail to passenger side frame rail. This receiver is confirmed to fit the 2014-2021 Chevrolet/GMC Express/Savana Cutaway Chassis. If…

view full answer...

Answer 2

From where the mounting brackets on the Buyers Products 2" Hitch Receiver #3371801102 will meet up to the frame of your GMC van down to the top of the receiver opening measures 7" (see attached).

view full answer...

Answer 3

The Buyers Products 2" Hitch Receiver For GM Express/Savana with Cutaway Chassis part #3371801102 will fit the frame just fine on a Chevy 3500 Shuttle Bus but the bumper is where things can cause problems as not all hang down the same amount.…

view full answer...

Answer 4

Buyer's Products does indeed recommend the #3371801102 for your cutaway van chassis, but to determine if the hitch will work, you'll need to measure for the drop needed. You do this by measuring downward from the underside of the frame member…

view full answer...

Answer 5

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 6

The only type of trailer hitch that may work on a school bus like your 2001 GMC Thomas School Bus is an adjustable hitch like the Curt #13703. This is a universal type hitch that will fit box, C-channel, or I-beam frames that are 22 inches to 72…

view full answer...

Answer 7

We do have some options available for your 2000 Ford E-450 Chassis but unfortunately a custom-fit hitch is not available. What you need is the Draw-Tite Ultra Frame Service Body Trailer Hitch. This hitch fits vehicles with frames up to 44" so…

view full answer...

Answer 8

Your 2012 Express Shuttle Bus would be built on the cutaway chassis version of the 2012 Express Van so that means the correct hitch you'd need is the Buyers Products part #3371801102 which was made for this style of chassis. I attached a picture…

view full answer...

Answer 9

I do have an option for you but there aren't any custom fit trailer hitch options for a 2006 Thomas School Bus. That said, we do still have universal options which can be installed either via welding or cutting/drilling. For this, I recommend the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Mounting Hole Dimensions of Buyers Products Trailer Hitch for GM Van Cutaway

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching