Curt or Draw Tite Hitch for 2020 Toyota RAV4

Question

Question:

Should I get the Curt C31416 or the Draw Tite # DT82QR for my 2020 Toyota RAV4?

asked by: Bill

0

Expert Reply:

I'd recommend the Curt hitch part # C13416 over the Draw Tite # DT82QR for your 2020 Toyota RAV4. Our installers have shared with us that the Curt hitches tend to have a bit tighter quality control and end up fitting a bit easier. Plus they are assembled in the USA.

I attached an install video and a picture of the hitch installed for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We have installed and tested the EcoHitch Hidden Trailer Hitch Receiver #EH97FR on a 2021 Toyota RAV4 with the hands-free lift gate feature and it still continued to work after the receiver was installed. I have linked the installation video below…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hello Mike, thanks for reaching out. We do offer a few different hitches for the 2026 Subaru Crosstrek, the Curt #C22MJ, the Draw-Tite #76209 and the EcoHitch #EH57CR. All 3 of these hitches place the receiver in virtually the same position beneath…

view full answer...

Answer 12

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Curt or Draw Tite Hitch for 2020 Toyota RAV4

Featured Help Information

Miscellaneous Media

Continue Researching