Replacement Clamp Assembly for Yakima Slim Shady Awning

Question

Question:

The slide wedge inside the mount and bolt. Can that be purchased separately?

asked by: Bobby M

0

Expert Reply:

I have a solution for you, but those parts are not available from Yakima at this time. Instead, you'll need to replace the entire assembly on your Yakima Slim Shady Awning # Y36VR. You can use the Replacement Clamp Assembly for Yakima SlimShady Roll-Out Awning # 8880737.

expert reply by: Erik B

0

click to enlarge

Answer 1

Hi Mike; we have confirmation that the #8880736 will fit Roam awnings but it hasn't been tested on a 99 CVT Pioneer so I can't guarantee it will fit. There is no adapter unless you want to have one custom fabricated. I attached a diagram…

view full answer...

Answer 2

To install the replacement clamp assembly #8880737 and bracket #8880736 on the Yakima SlimShady Awning #Y36VR, there are two t-bolts that are inserted into the upper channel of each side of the SlimShady rail. You would then place the clamp onto the…

view full answer...

Answer 3

I do have a solution for you but unfortunately the Yakima SlimShady Awning #Y36VR does not have any side panels that you can add. We do have the Rhino-Rack Sunseeker Awning #RR32132 though which is a little bit larger and is comparable to the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement Clamp Assembly for Yakima Slim Shady Awning

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching