Curt Hitch C13073 versus Draw-Tite 75684 for 2011 Hyundai Santa Fe
Updated 05/15/2012 | Published 05/14/2012
Products Featured in This Question
Question:
What is the difference between Curt C13073 versus Draw-Tite 75684? One seems to be squared tube and the other round tube. Which is better? Thanks.
asked by: Chin T
Expert Reply:
Curt offers a round tube Class III receiver, part # C13073, but to satisfy their warranty requirements, a stabilizer strap # 18050 needs to be used for non-trailer loads like a bike rack or cargo carrier. If you intend on only using the receiver for towing, the Curt would be a good choice.
The Draw-Tite # 75684 is constructed of square-tube steel. Because of the spoiler on top of the hatch, the stabilizer strap will not work well on the Santa Fe, so for a bike rack or cargo carrier, the Draw-Tite hitch would be a better choice as the strap is not needed.
Both hitches would fit your 2011 Santa Fe as long as it does not have a dual exhaust, with the tailpipe on drivers and passenger side.
There is not an available hitch for the Santa Fe with dual exhaust.
To complete your towing system, you might also need the following:
Trailer wiring harness, part # 118415, or # 118258 for vehicles equipped with the tow package
Ball mount, part # D-4
1-7/8 inch trailer ball, part # 19260
2 inch trailer ball, part # 63845
Pin and clip, part # PC3
Locking hitch pin, part # e98882
I have linked you to install instructions and videos.
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: th934xtr
- Search Results: hitch bike racks
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: T-One Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Will Rear Hatch Open With Trunk-Mounted Bike Rack Installed on 2011 Kia Sorento
- Q&A: Installing Curt Class III Trailer Hitch on 2013 Kia Sorento SX with Factory Tow Prep Package
- Q&A: Trailer Hitch and 4-Bike Carrier for a 2011 Kia Sorento
- Q&A: Cleaning Threaded Holes on a 2011 Kia Sorento to Install a Draw-Tite part # 75684
- Shop: Nylon Tube Brush - 3/8"
- Shop: Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
- Shop: Cleaning Brushes - Brass, Nylon, and Stainless Steel Bristles - Multi Purpose - 3 Pieces
- Q&A: How to Determine if 2012 Kia Sorento Has Factory Tow Package
- Q&A: Recommended Trailer Hitch and Wiring for 2011 Hyundai Santa Fe with Spare Tire Under Vehicle
- Q&A: Parts Needed to Install the Curt Discovery Brake Controller # C51120 on a 2013 Dodge Durango