What Size Diameter Tubes Does the Replacement Cradle Set Y8890177 Fit?

Question

Question:

What size tube will this part work on? My Yakima rack has 1 1/4 inch tubes.

asked by: Richard G

0

Expert Reply:

The Replacement Cradle Set # Y8890177 works with tubes 1-1/4" in diameter, so this will work on your Yakima rack that you've specified has 1-1/4" tubes. For reference, it's likely that you have a Yakima DoubleDown rack similar to the DoubleDown 4, which has 1-1/4" diameter tubes (it also comes in 2 bike or 5 bike configurations).

expert reply by: Erik B

0

Answer 1

Hey Dan, thanks for reaching out! Yes, the Replacement Anti-Sway Cradle #Y8890177 will fit your older Yakima BigHorn bike rack. Is there anything else you're needing to upgrade or replace on the rack while you're at it?

view full answer...

Answer 2

We do have the replacement rubber straps for your Yakima BigHorn Bike Rack with part #8890221, however the replacement cradles are no longer manufactured by Yakima. Since this particular rack is no longer in production, your best option is really…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

What Size Diameter Tubes Does the Replacement Cradle Set Y8890177 Fit?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching