Is Play Between Channel Mounted Coupler and Channel Normal

Question

Question:

How tight should a channel mount coupler like the titan fit in the channel? If there is extra space, should it be taken up with steel washers?

asked by: Keith

1

Helpful Expert Reply:

A little bit of play between the coupler and the channel is normal. As long as the bolts are properly torqued, the play won't damage or harm anything.

We've confirmed this with our channel mount coupler manufacturers like Bulldog and Titan.

expert reply by: Jameson C

1

Answer 1

Hi Robert, When you're installing the Demco 2-Bolt Channel Mount Coupler Hardware Kit part #DM68UV, the washer will go onto the threaded end once the bolt is put through the frame and the lock nut tightened down onto the washer. I've included…

view full answer...

Answer 2

Hey Bill, there is some play between the Dexter Trailer Coupler part #T1882000 and the channel it attaches to in the review video because Adam did not torque the hardware down like you normally would during the install process. Is the play you have…

view full answer...

Answer 3

A little bit of play between the coupler and the channel is normal. As long as the bolts are properly torqued, the play won't damage or harm anything. I've confirmed this with my Bulldog representative.

view full answer...

Answer 4

First I want to make sure you verify your channel mount for the Demco Trailer Coupler #DM14040-81 has a 21K or larger capacity as often times they are less like the Demco #DM15349-52 which often times people look at and think it is a channel mount…

view full answer...

Answer 5

Good question; the bolts in the Hardware Kit for Demco Adjustable Channel Mount Couplers #DM6166 should be torqued to 150 lb-ft during install of a Demco coupler like #DM14040-81 to a bracket like #DM66134.

view full answer...

Answer 6

Adjustable trailer couplers are not going to mount to your truck; they will attach to the frame of your trailer. Some of the adjustable couplers, such as the Bulldog Cast Head #BDA2563C0317 come with the mounting hardware to weld onto the frame of…

view full answer...

Answer 7

When mounting a cast head coupler like Bulldog #BDA256C0317 to its mounting channel you will want to torque the mounting bolts to the specification indicated by the manufacturer in the instructions. The torque spec will vary from coupler to coupler.…

view full answer...

Answer 8

To get the full capacity of the Pro Series Adjustable-Channel Coupler #PSA256S0303 there shouldn't be any space between the coupler and the channel like the part #BDAC5000300. You can either torque the coupler down more to take up that gap if…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Is Play Between Channel Mounted Coupler and Channel Normal

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching