Does Curt Trailer Hitch Sit Against Bumper for 2010 Subaru Outback Wagon
Updated 08/21/2019 | Published 08/20/2019
Question:
Hello I have a 2010 outback 2.5 Im curious how far this hitch sticks out horizontally past the bumper, if at all Im also curious if this hitch fits up snug against the underside of the bumper. Im trying to minimize clearance loss. Thanks in advance!
asked by: Cullen M
Expert Reply:
The Curt Trailer Hitch Receiver # C13410 will fit up snug against the bumper of your 2010 Subaru Outback Wagon and if you reference the linked instructions you can see that you actually need to trim some of the bumper fascia. As for how far out past the bumper it sits, I'm not quite sure because we haven't installed it on a 2010 Outback Wagon yet (August 2019). I did go out to the warehouse though and found that from the back side of the mounting brackets to the outermost edge of the receiver was about 8-1/2". If you really wanted to see where the receiver sits you would have to remove your bumper and measure from where the hitch sits against the frame like the instructions calls out.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Q&A: Which Hitch is Better for a 2016 Subaru Outback Wagon?
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Installed Height of etrailer Brand Hitch Receiver e98847 on 2019 Subaru Outback Wagon
- Q&A: Best Hitch Comparison for 2018 Subaru Outback Wagon
- Q&A: Ground Clearance Of Curt and Draw-Tite Hitch Options For 2019 Toyota RAV4 Adventure
- Q&A: Recommended Hitch, Wiring Harness, and Ball Mount for a 2010 Subaru Outback Wagon
- Q&A: Ground Clearance of Curt C13410 Class III Hitches
- Q&A: Curt C13410 vs. Draw Tite 76227 Trailer Hitch Receiver for 2015 Subaru Outback
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer hitch
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: trailer wiring
- Video: How to Choose a Trailer Brake Controller
- Article: Trailer Wiring Diagrams
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Suspension Enhancement
- Search Results: trailer tires and wheels
- Article: How to Choose the Right Trailer Hitch Class
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer jack
- Video: Clean Up Your Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Hitch
