Lug Nut Needed for 1987 Boat Trailer Thats Removed with 13/16 Socket

Question

Question:

I have 1987 boat trailer I use a 13/16 socket to get them off. what size lug nut are they

asked by: Dan S

0

Expert Reply:

You should be able to use the Americana Trailer Wheel Lug Nut # AM26NR. This fits 1/2" - 20 studs so just make sure that's what you have prior to ordering. You can verify this by measuring the diameter of your studs as the thread count should match up just fine for 1/2" studs.

expert reply by: Jon G

0

Answer 1

Hey Robert, our trailer wheel and tire combos like the Strider ST235/80R16 Radial Trailer Tire w/ 16" Revolver Black Mod Wheel #TA27AR are not balanced as generally people don't balance trailer wheels. The weights don't stay on trailer…

view full answer...

Answer 2

The wheel/tire combos we offer are not balanced at the factory. When the tire is mounted to the wheel, the high or heavy spot on the wheel is matched to the low or light spot on the tire, which leaves the wheel and tire somewhat balanced. You can…

view full answer...

Answer 3

Hi Tim; I can get you everything aside from the hangers. All of our standard hangers are designed to weld on but you may be able to find that bolt-on style elsewhere online or at a local shop. Hangers like those do still exist although I'm not…

view full answer...

Answer 4

The special trailer wheel/tire products we sell, such as Taskmaster 5.30-12 Bias Trailer Tire/Wheel #TA26RR, have not been given a full dynamic balance like passenger vehicle tires get when mounted. But what the distributor does is match up the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Lug Nut Needed for 1987 Boat Trailer Thats Removed with 13/16 Socket

Product Page this Question was Asked From

Continue Researching