Instructions for Replacing Cab Clamp of Extang Trifecta Tonneau Cover
Updated 06/16/2025 | Published 03/18/2019
Products Featured in This Question
Question:
Removing existing clamps, brand new cover but stripped to the point of the whole bolt turning. Called and am receiving new front clamps from your company. Just wondering are there any instructions on how to remove and install new clamps. Could not turn wing nuts by hand needed channel locks to try to turn old ones. Bought it because of ease of installation.
asked by: Kenneth V
Expert Reply:
I spoke with my contact at Extang about the install of the front clamp for Trifecta Cover part # EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly will then be able to slide out of the rail.
Product Page this Question was Asked From
Replacement Cab Clamp Assembly for Extang Trifecta Tonneau Covers - Qty 1
- Accessories and Parts
- Tonneau Cover
- Clamps
- Extang Trifecta
- Extang
more information >
Continue Researching
- Video: A Closer Look at the Replacement Cab Clamp Assembly for Extang Trifecta Tonneau Covers
- Shop: Replacement Cab Clamp Assembly for Extang Trifecta Tonneau Covers - Qty 1
- Shop: Replacement Tail Clamp Assembly for Extang Solid Fold 2.0 and Trifecta Tonneau Covers - Qty 1
- Shop: Replacement Tail Clamp Assembly for Extang Solid Fold Tonneau Covers - Qty 1
- Q&A: Are Extang Tail Gate Clamps aka EZ-Lock Clamps Compatible with First Generation Solid Fold
- Shop: Ark Articulating Off-Road Coupler for 2" Receivers - Trailer Side - 2" Ball
- Shop: Lock N Roll Articulating Coupler - A-Frame - Trailer Side - 11K
- Shop: Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers - Qty 1
- Shop: Replacement Jaw Grip Clamp for Extang Solid Fold 2.0 Tonneau Covers - Qty 1
- Video: Review of the Ark Articulating Off-Road Coupler for 2" Receivers
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2023 Ford Bronco Sport
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: Feature Breakdown: Replacement Jaw Grip Clamp for Extang Solid Fold 2.0 Tonneau Covers
- Shop: Ladder Rack
- Shop: Vehicle Tow Bar Brake System
- Q&A: Extang Trifecta 2.0 Replacement Clamp Instructions
- Q&A: How Does Replacement Clamp for Extang Trifecta EX1034 Install
- Q&A: Install Instructions for Extang Trifecta Cover Clamp part # EX1034
- Shop: Tonneau Cover
- Q&A: Replacing The Front Clamp On The Extang Trifold Cover
- Search Results: xtang
- Video: Replacement Tailgate Hinge for Extang Trifecta 2.0 Folding Tonneau Covers: The Breakdown
- Q&A: How to Replace the Rear Tailgate Clamp on an Extang Trifecta 2.0 Tonneau Cover
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Search Results: trailer wiring
- Article: How to Measure for Trailer Hitch Drop
on Accessories and Parts
Trukin72
6/16/2025
Or if the bolt or screw is ok but clamp and or wing nut is all you are replacing, just screw old off completely and replace with new parts without disturbing the T that slides in the track. I just did this on my Ridgeline cover.