Fulton F2 Jack Mounted on a Ranger RT188 Trailer

Question

Question:

Thought I would send you another customer photo of what the Fulton F2 Jack looks like mounted up on the trailer. FYI, the dual wheel model will contact the frame on this particular Ranger Trail trailer, but the single wheel seems to do fine.

asked by: Kenneth E

1

Helpful Expert Reply:

Thanks! I attached the picture you submitted so that other customer can see what the Fulton F2 part # F1413140334 looks like installed on Ranger RT188 trailer.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I think the Fulton F2 Swing-Up Jack is a good choice. The model for 4 - 5" frames is #F1413140334. The 1600 lb. tongue weight rating is much more than you need, but won't affect the function of the jack. The height will work and it will get…

view full answer...

Answer 2

You can get the Fulton F2 Adjustable A-Frame Trailer Jack #F1413250334 but take some measurements to see if it will fit in your A-Frame coupler. I've included a diagram for you! The plate that mounts to your A-Frame coupler is 5 inches in…

view full answer...

Answer 3

According to my contact at Fulton, their 1600-lb capacity F2 Swing-Up Trailer Jack #F1413140334 will fit your 5-1/2-inch tall x 2-inch wide trailer frame with the included U-bolt mounting hardware. The jack is designed to fit 2-inch wide trailer…

view full answer...

Answer 4

There typically isn't going to be that type of information on a jack, but if you can find a part number somewhere you'll likely be able to find that information by cross referencing it on our site or another. With that said, it sound like you…

view full answer...

Answer 5

Dutton-Lainson jacks are manufactured right here in the US and are actually really good quality. The mount used by your current Dutton-Lainson jack wouldn't be compatible with the Fulton F2, which leaves you with a couple of options. You could…

view full answer...

Answer 6

The Fulton F2 Swing-Up Jack w/ Pivoting Footplate - 5" Frame, Weld On #F1413200334 has a cast steel mounting plate. The rounded part of the jack is aluminum but other components are steel like the swivel housing according to my contact at…

view full answer...

Answer 7

I spoke with my contact at Fulton and he confirmed that both the Fulton XLT #F141133 and the F2 Swing-Up #F1413040134 will fit your trailer frame that measures 3 inches x 1-1/2 inches. Typically bracket height is measured from the bottom of the wheel…

view full answer...

Answer 8

The 20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground #A20WB simply has two wires that connect to the running light pin of the 4-way. There isn't a 5 wire we carry in spools or by the foot, but we do carry the Bonded 4 Wire -…

view full answer...

Answer 9

The Fulton F2 Swing-Up Trailer Jack you referenced, part #F1413040134, has according to my contact at Fulton a bolt pattern of 3.44 inches X 4.44 inches measured precisely from hole center to hole center, top to bottom and side to side, respectively.…

view full answer...

Answer 10

The Fulton F2 Swing-Up Trailer Jack #F1413040134 referenced in your question features a lubricated 1-piece gearbox that reduces the need for period manual lubrication but you can certainly add extra grease when needed using the ventilation port. You…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Fulton F2 Jack Mounted on a Ranger RT188 Trailer

Continue Researching