How to Determine Correct E-Z Lube Grease Cap
Updated 02/04/2019 | Published 02/03/2019
Products Featured in This Question
Question:
I lost a dust cap for my 2012 Springdale 293. I have the old one, but its too beat up to measure. Wondering where i can find the correct ez-lube drive in cap?
asked by: John W
Expert Reply:
To determine the correct E-Z Lube grease cap you are going to need to measure the center of the hub where the grease cap is going to fit (please see accompanying photo). The measurement will need to be very precise, so you are going to want to use a digital caliper such as # PTW80157.
You will then just compare that to the available caps.
Grease Cap # RG04-040 will fit a hub bore of 1.99 inches.
Grease Cap # RG04-080 will fit a hub bore of 2.44 inches.
Grease Cap # RG04-120 will fit a hub bore of 2.72 inches.
I have added links to video reviews of each of these caps as well as a link to our entire selection of E-Z Lube grease caps should one of these not be the correct size.
Product Page this Question was Asked From
Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- EZ Lube Grease Cap
- 1.99 Inch O.D.
- 1.99 Inch
- 2000 lbs Axle
- 2200 lbs Axle
- 2500 lbs Axle
- 3000 lbs Axle
- 3500 lbs Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Replacement Magnet Kit for 12" Electric Trailer Brake Assemblies - 5,200 lbs to 7,000 lbs
- Shop: Grease Cap, 2.44" OD Drive In with Plug - Qty 2
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Search Results: dexter axle grease caps
- Shop: Dexter's E-Z Lube Grease Cap and Plug Kit - 2.45" Outer Diameter
- Shop: EZ Lube Grease Caps with 1.99" OD - Fits 7" and 10" x 1-1/4" Dexter Hubs - Qty 2
- Shop: 2" Lubed Dust Cap & Rubber Plug - 1.99" x 1.40" x 1.18" - Qty 1
- Search Results: trailer lights
- Search Results: trailer bearings races seals caps
- Search Results: dexter axle grease cap
- Search Results: dexter grease cap
- Search Results: bearing caps
- Search Results: brake magnets
- Shop: Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End - 3 Gauge - 16' Long
- Shop: Suspension Enhancement
- Q&A: Replacement for Dexter Cap Kit K71-317-00
- Q&A: How to Determine the Weight Capacity of a Dexter Axle Based Off the Inner and Outer Bearings
- Q&A: How to Measure a Hub to Determine the Right Grease Cap to Use
- Q&A: Replacement Dust Cap For Dexter 5,200LB E-Z Lube Trailer Axle
- Article: Most Popular Wheel Bearings
- Q&A: How to Tell if I Have an EZ Grease Hub or a Standard Hub
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: What Brakes and Bearings do I Need for My PJ Dump Trailer with Tandem 7K Axles?
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Trailer Wiring Diagrams