Replacement Rear Hinge for Yakima SkyBox 18

Question

Question:

Hi there, I need a rear hinge for my skybox 18, I only see the front one? It is the 2009 and later model

asked by: Timothy A

0

Expert Reply:

The correct rear hinge for your Yakima SkyBox 18, like part # Y07336, is the Replacement Lid Support # 8880683. I spoke with my contact at Yakima who confirmed this as well.

expert reply by: Jon G

0

Answer 1

You will need part #8880683 for the rear support and part #8880684 for the front support.

view full answer...

Answer 2

The Yakima SkyBox 18 Rooftop Cargo Box - 18 cu ft - Black Carbonite #Y07336 rear support is #8880683. The front support is 8870089 as you stated but it has been discontinued. I've linked the page to other Yakima roof box parts in case there is…

view full answer...

Answer 3

I confirmed with my contact at Yakima that the length of your box fits the dimensions of the older Yakima SkyBox 18 #Y07336 or the older Yakima SkyBox 21 #Y07337. Both the SkyBox 18 and the SkyBox 21 use the same replacement rear and front supports.…

view full answer...

Answer 4

So even though your Yakima SkyBox 18 #Y07336 or SkyBox21 #Y07337 has the diamond shaped hinges currently, those are an older model hinge that is no longer used by Yakima; you also won't be able to use the Replacement Front Lid Support 8870090…

view full answer...

Answer 5

You can buy the front and rear lid supports for your Yakima SkyBox 18 #Y07336 right here! For the front lid support you need Replacement Lid Support #8880684 while for the rear lid support you need Replacement Lid Support #8880683.

view full answer...

Answer 6

The correct updated front and rear hinge/lid support for a Yakima Skybox 18 is the Replacement Lid Support for Yakima Cargo Boxes part #8880683 for the front and then the Replacement Lid Support for Yakima Cargo Boxes part #8880684 for the rear. I…

view full answer...

Answer 7

The Yakima Skybox 21 part #Y07337 made from 2014 to present has a much more aerodynamic shaped lid than the Yakima Skybox 21 part Y07184 made from 2009 to 2014 had. I have attached a photo of each so you can see the difference. If you have the 09-14…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Rear Hinge for Yakima SkyBox 18

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching