Yakima Railgrab Tower Replacement Adjustment Knobs

Question

Question:

I recently purchased the Yakima rail grab system used and 3 of the 4 clamps have shredded screws where you would tighten the black knob. What replacement parts would I need to fix this? I cannot get the screws out so I am thinking I will need to replace the whole clamp part. I am planning to put this on a 2016 Nissan Rogue SL with factory roof rails.

asked by: Mallory

0

Expert Reply:

While the Yakima Railgrab roof racks are being phased out and not what Yakima currently recommends for your 2016 Mazda CX-5 I was able to determine that they were the correct fit for your 2016 Mazda CX-5 with raised rails.

The replacement kit that includes the screw is the # Y8880150. If you need the adjustment knobs instead you'd want the # Y8880148 which I believe is what you meant since you mentioned a black knob.

expert reply by: Jameson C

0

Answer 1

It sounds like you are describing the screw that comes with the Replacement Wedge Assembly #Y8880150. The screw only comes with this kit. The only other possibility is #Y8880148 which are the adjustment knobs for RailGrab towers.

view full answer...

Answer 2

The replacement screw you are looking for is available in the Replacement Wedge Assembly for Yakima RailGrab Roof Rack Towers #Y8880150.

view full answer...

Answer 3

The discontinued Y8880205 does not include the bolt but the #Y8880150 which is the matching wedge assembly does include it.

view full answer...

Answer 4

For replacement bases for the Railgrab you would want the part #Y8880279. This also comes with a new brass nut.

view full answer...

Answer 5

If you don't have the Replacement Adjustment Knobs #Y8880148 then you will need them to attach the Replacement Large Claw Assembly #Y80144. The knob is what allows you to attach the claw assembly to the Upper Claw Base #Y8880279 on your RailGrab…

view full answer...

Answer 6

Sounds like you are looking for the Yakima Railgrab Wedge Assembly and Bolt part #Y8880150 which comes with the Allen bolt you are looking for.

view full answer...

Answer 7

The Yakima RailGrabs, which replaced the LowRider line of towers, and is now itself discontinued, did not have any changes to the hardware over its life span so #Y8880279 will fit your RailGrab towers. If you need the wedge assembly it is #Y8880150.…

view full answer...

Answer 8

We have the replacement screw you are looking for with the part #Y8880150 which matches up to the nut of the #Y8880279 which is M6.

view full answer...

Answer 9

It sounds like you are looking for the Replacement Adjustment Knobs for Railgrab part #Y8880148.

view full answer...

Answer 10

We do carry replacement parts for the Yakima Railgrab foot. For the claw base and nut you would want the part #Y8880279. The medium claws are no longer available. For the claws with pin adapters you would want the part #Y8880201. For replacement…

view full answer...

Answer 11

The long, black screw you referred to is not available as a replacement part. The only screw that is would be the silver one you mentioned which comes with the Replacement Wedge Assembly for Yakima RailGrab Roof Rack Towers #Y8880150.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Yakima Railgrab Tower Replacement Adjustment Knobs

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching