Flush Mount Grommet and Wiring Pigtail for 2 Inch Clearance and Side Marker Lights

Question

Question:

where are the 2inch grommets to mount the 2inch side marker lights

asked by: Fran

0

Expert Reply:

The Sealed, 2" Round Trailer Clearance and Side Marker Light, Flush Mount - Amber # MC53AB or the LED # MCL55AB will use the 2" Round Grommet - Flush Mount - Open Back # A54GB for installation. You will also require the wiring pigtail # A46PB which will give you 6 inches lead.

expert reply by: Jason S

0

Answer 1

The Loadstar ST175/80D13 Bias Trailer Tire with 13" White Wheel #AM31233 that you referenced has a 1,610 lbs at 65 psi weight capacity per wheel/tire. For your trailer that is towing a 3,500 lb boat this should work well since your trailer has…

view full answer...

Answer 2

All other things being equal, it is always preferable to have matching tires on your trailer. Different tire brands may have different tread depths and may wear at different rates due to variances in the formula used in their rubber compound.…

view full answer...

Answer 3

I have a couple options for you as we do not have a box like the Buyers Products Tail Light Mounting Box #337LB383SL with a opening on the side for the Peterson LED Clearance and Side Marker Trailer Light #PE57PR. First would be to drill a 3"…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Flush Mount Grommet and Wiring Pigtail for 2 Inch Clearance and Side Marker Lights

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching