Ultra-Fab T-Slot Power Drill Adapter Slot Dimensions

Question

Question:

Please tell the width of each of the 2 slots. One of the comments has a nice pic showing other dimensions of the tool, but not the slots’ width.

asked by: Fred Y

1

Helpful Expert Reply:

The Ultra-Fab T-Slot Power Drill Adapter for Scissor Jacks # UF48-979071 will have a slot that is 1/4 inch wide. I've attached that new dimension to the product photo for you.

expert reply by: Jason S

1

click to enlarge

Answer 1

Since Atwood has gone out of business, their replacement parts are pretty hard to find. With that being said, the: -Replacement Crank Handle for Stromberg Carlson Landing Gear #LG-119226 will fit most Atwood jacks, however this crank handle will be…

view full answer...

Answer 2

There are a few different drill adapters for different jacks. The hex head #UF48-979005 sounds like what you describe so we know it won't work. The other type is what is called a T-Slot such as #UF48-979071. It has a shaft length of 2.5 inches,…

view full answer...

Answer 3

The original Atwood manual crank you are looking for is no longer available but we have the Replacement Crank Handle for Stromberg Carlson Landing Gear #LG-119226 that will work for your Atwood Electric Jack. This is a much longer option which would…

view full answer...

Answer 4

Hello John, sorry to hear the drill adapter is not working for you. Our records show your Atwood MPD 86065 electric jacks would use a drill adapter that is 0.53" in diameter. The #UF48-979071 adapter is more like 0.66" so too big. We used…

view full answer...

Answer 5

I went and pulled an Ultra-Fab T-Slot Power Drill Adapter #UF48-979071 from our warehouse to measure the inside diameter of the open end of the adapter and found that it measures .627 inches or 15.9 mm.

view full answer...

Answer 6

The Atwood manual crank you referenced we no longer carry. The Replacement Crank Handle for Stromberg Carlson Landing Gear #LG-119226 is the manual crank we have that will work for your Atwood Electric Jack. This is a much longer option which would…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Ultra-Fab T-Slot Power Drill Adapter Slot Dimensions

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching