Tire Valve Extenders for 2018 Coachmen Leprechaun Class C Motorhome

Question

Question:

Hey Guys, what tire valve extenders wold yo suggest for the above unit. I see you posted for the Ford 450, need a set for my coach. I will pass the info alone to the hundreds of members on our Facebook page also. Will include pictures.

asked by: Jack O

1

Helpful Expert Reply:

Usually 45-deree valve extenders like the Wheel Masters # WM8029 which you referenced are the best bet but we also have 135-degree extenders # WM8029135 for when a sharper bend is needed.

Another way to go is the Wheel Masters 4-Hose Inflation Kit # WM8001-135. This kit will let you relocate the inner tire's valve stem to the outer wheel while also extending the valve stem on the outer tires.

expert reply by: Adam R

1

Answer 1

Thanks for the pictures, I can see why you're concerned now. It looks like you have some 135 degree valve extenders that just aren't quite long enough to pass through the hand holes of the wheel cover. You could try using a longer 180 degree…

view full answer...

Answer 2

Thank you for the picture that really does help figure out what'll be best for you. It appears for your right/left rear outside tires, you could benefit from an extender that has a bend in it, like the Wheel Masters Tire Pressure Valve Extenders…

view full answer...

Answer 3

Thanks for the picture of your wheel and valve stem setup. I'd recommend 135 degree valve extenders like the part #WM8029135 as this will put the valve stem at a better angle than a 180 degree kit. These will work great with your current wheel…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The differences between the Firestone Ride Rite #F2613 and the Red Label #F2709 for your 2023 GMC Sierra 3500 Crew Cab Long Bed is the air pressure and max weight capacity. The Ride-Rite #F2613 are rated for 5,000lbs and 100 PSI, where the Red Label…

view full answer...

Answer 10

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 11

Hey Kurt, yes the correct gap for SumoSprings Solo kits like the part #SS88UV is 1/2 inch to 1 inch like you mentioned. Did you install this already?

view full answer...

Tire Valve Extenders for 2018 Coachmen Leprechaun Class C Motorhome

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching