Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
These angled valve extenders make it easy to access the valve stems on your front tires. Each sturdy, nickel-plated brass tube is bent at a 45-degree angle and screws onto your existing valve stem. Includes 2 extenders with caps.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to be taking a look at the Wheel Masters Valve stem Extender. Valve stem extenders are going to be great for extending your valve stems out to make them a lot more accessible. Let's face it, on a motor home, we have these nice caps on, but the valve stems kind of sit back inside the hole a little bit, so it makes it a little bit difficult when you're trying to add air pressure or just checking the pressure altogether. So, let's say we wanted to add a tire pressure monitor system. Tire pressure monitor system has a sensor that screws on to the end of the valve stem. If you do not have an extension, the tire pressure monitor system sensor is not going to fit inside of there.
So again, adding these on is going to make it much easier. Not only now, but in the long run. You can see they're going to have a 45 degree angle on them. So, it gives the end of that out pretty far. So, it makes it easy to access.
They're going to be a solid nickel alloy coated brass. They're going to come with new valve stem tips. So, when this is put on to your old valve stem or your factory valve stem, it is going to come with a new cap. These are going to be designed for your front wheels. They're going to come in a set of two.
There are other valve stem extenders available. You can find those here at etrailer, For example, u-shaped, there's flexible lines. What I recommend is check in to see how your factory valve stem is set up with your cap to make sure you pick up the correct ones. Who's going to do it for Look At The Wheel Masters Valve Stem Extensions..
The stem extensions are high quality and well made. They allow me to mount my TPMS sensors without removing the wheel covers. For some reason the angled ones don’t work with my digital tie gauge, but they do work with my pencil one. I haven’t yet tried to use my small air compressor yet; I hope it works with them. I may email your support group to see if there’s something I can try to get them to work with my main gauge. I was very satisfied with the price, ease of ordering and rapid shipping.
It would have been helpful if the description on line reference front or rear use. I need something for the rear inner wheel and the 45 degree extentions are a little too much angle and too short. Otherwise a good product.
Even those these wear out after 8 years I still love that they allow me to snake the air valves for my inner rear tires on my Ford F350 dually through the aluminum outer wheels' tiny little holes in the rim for access to check the pressure and adjust the air pressure, particularly on long trips pulling my travel trailer.
Leaks at TMP sensor side. Had to snug it good to valve stem and it did not leak. Cannot get TMP side to seal.
They leak, what else can I stay? I didn’t over tighten them, I sprayed soap water and 3 out of 6 were leaking on the tire side. I but them on shortly after our Tire Minder started shrieking. I give up removed all of them and replaced the tpms sensors onto the tire valves and voilà no more leaks.
My hands are small enough to fit into the oval holes in the steel rims.
I bought these to extend the fill point for a couple of motorcycle air shocks and they weren't compatible with the fitting on the shock but for a regular application, I'm sure they would be great. As usual, fast shipping and a good price from Etrailer.
Valve extensions work great. Be sure that you have steel valve stems as they are hard to fill when you attach them to rubber valve stems.
Makes it much easier to check your tires without having to remove your wheel covers
I have not used these extenders yet. I was not sure how much curvature I needed when I ordered. Product appears to be of good quality. May return or use on front wheels since the 135 degree extensions worked so well on the rears.
Valve extenders work great in my RV. Easy to install and they are made of superior materials. Had cheaper ones that didn’t last long. These are made to last and work great.
These extenders allowed me to mount flow through sensors on the front wheels of my motorhome. Without them, it was nearly impossible to even check air pressure.
Worked as intended.
These were very easy to install and were just as described - liked the price - shipped
quickly and the quality was well above what I expected - still on motorhome and no
leaks - makes checking air pressure a breeze now!
They hold tire pressure,no air leaks. Happy with the product.
Valve extenders worked perfectly.
These valve extenders were great and looks fine.
This product was exactly what I needed for my motor home. High quality and great service.
Have looked all over for these valves...they are perfect...Mercedes sprinter
Arrived quickly and the valve extenders fit perfectly on the motor home.
Fast, Reliable, Professional, and always in my budget. Second to none.
Works good
Quality and priced right. Convienient RV
Extension. Heavy duty
Enables easy access to air up and check pressure on dual tire applications.
Have not installed them yet. Plan to this spring.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Stephen
10/22/2022
Great! No issues what so ever.