Does Curt T-Connector Trailer Wiring Kit # C55369 Plug Into Vehicle Wiring

Question

Question:

it gives directions that it will fit and plug into existing wiring harness, then it says not ???

asked by: Mac E

0

Expert Reply:

The Curt T-Connector trailer wiring harness part # C55369 that you referenced does plug into existing wiring with the green connector opposite of the 4-way connector. I attached an install video for this kit for you to check out as well.

expert reply by: Jameson C

0

Answer 1

7-Way trailer connector #HM42190 for a 2001 Jeep Grand Cherokee looks similar to a 4-Way but the end that plugs into the vehicle has 7 pins in it for the 7 functions on the connector. It is not a confirmed fit though unless the vehicle originally had…

view full answer...

Answer 2

I went over the install instructions for the Curt trailer wiring harness and there is no mention of needing to install the ring terminal that's included. That said the trailer wiring harness I recommend for your 2004 Jeep Grand Cherokee is the…

view full answer...

Answer 3

To install the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C55369 you linked to in your 2002 Jeep Grand Cherokee without factory tow package you'll need to do the follow steps: 1. Remove the rear threshold seen in…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Does Curt T-Connector Trailer Wiring Kit # C55369 Plug Into Vehicle Wiring

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching