Dimensions for 10-19 Grease Seal

Question

Question:

difference between 10-19 and 10-20 seal

asked by: Bill

0

Expert Reply:

A 10-19 grease seal like # RG06-050 features an inner diameter of 1.719 inches and an outer diameter of 2.565 inches. I have not heard of a 10-20 grease seal so I am not sure of its specific dimensions. If you are trying to replace an existing seal on your trailer, you will just want to make sure the inner and outer diameter matches what you currently have.

I have attached a short video on this seal that you can check out, along with a link that will take you to our available selection of grease seals that you can look through.

expert reply by: Chris R

0

Answer 1

Thanks for the picture! To replace your Marshal 605H propane regulator you will need to go with the Camco Vertical 2-Stage Propane Regulator #CAM59313. This will be an exact replacement for your current regulator. I included a video review of the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 6

We have a wide range of trailer hubs so we can get you all set. Our hubs include bearings, races and seals. The way to select a replacement hub is to match up the bearings to the original hub. A new hub must use the same bearings as the old one in…

view full answer...

Answer 7

My recommendation is to replace your axle with a 5,200lb like #e55SR as the 4,400lb spindle is so uncommon they are not readily available. This will give you stronger components to lessen the chance of you having to replace a spindle in the future.…

view full answer...

Answer 8

Hey Uriah, thanks for reaching out! The Tradesman Vaquero Self-Contained Hydraulic A-Frame Trailer Jack #ST86FR will work best if it's hardwired to a battery on your trailer, but you can also hardwire a 7-Way plug and lead like part #H20043 and…

view full answer...

Answer 9

I wish we had an easy solution, but we don't have magnets that will fit your application and we don't have a way to replace just the brake assemblies either as since what you have is welded directly to the trailer axle. So it will end up…

view full answer...

Answer 10

I was unable to see the photos you attached as it is blocked by our system but the casting numbers on your hubs are an old system that nobody goes by any longer. The brake assemblies with the welded backing plate have been outdated for decades and we…

view full answer...

Answer 11

Hello Al, Happy to get those for you. I would want to take a gander at them too, just to see what I’m getting myself into. I was able to get the instructions for the Advent Air Low Profile RV Air Conditioner System, Single Zone, 15,000 Btu, White,…

view full answer...

Dimensions for 10-19 Grease Seal

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching