Replacement Damper Lock Springs for Ventline Range Hood

Question

Question:

hinge lock pins broke off and would like to replace them. do you have the part? the damper and hood are fine just want to secure the damper again

asked by: Leanne

0

Expert Reply:

It sounds like you are needing the Replacement Damper Lock Springs # C0488-00. These lock springs are designed for Ventline P, B, and T Series Ventline Range Hoods and allows the damper to be locked in the closed position.

This will include 1 damper lock spring.

expert reply by: Chris R

0

click to enlarge

Answer 1

The Replacement Damper for Ventline RV Range Hood part #BCA0472-00 is the damper located in the hood. If this is indeed the damper you are referring to then the correct lock spring is the Replacement Damper Lock Spring for Ventline RV Range Hood part…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 4

Hello Dennis, We used to price match, but quit quite a few years ago. We try to keep our prices competitive, but sometimes there is someone out there with a better price =( I see you are looking at the Weigh Safe True Tow Weight Distribution Hitch -…

view full answer...

Answer 5

Hi Johnny! We don't carry the front spacers and control arms needed to give your 2026 Ford F-150 a 3" lift. Also, adding a lift will affect the fit of the SumoSprings since they are designed around the factory suspension height. If you leave…

view full answer...

Answer 6

Hey Dennis! I can't say if it will clear for sure but I can give you dimensions to help determine if it will. Using the furthest hitch pin hole, the Malone 2" Dual Purpose Hitch Receiver #MPG544 will push the bike rack out 12-1/4". When…

view full answer...

Answer 7

Hey Bob, welcome back and congrats on the new truck! To flat tow your 2025 Ford F-150 you'll need the following parts: Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms item #RM45EQ Wiring Harness - Roadmaster Universal…

view full answer...

Answer 8

Hey Dennis, thanks for reaching out! According to the Roadmaster fitguide you're going to need a brake light switch as well since they weren't able to locate the color of the OEM brake light circuit wire. You'll use part #RM42MR if you…

view full answer...

Answer 9

Hey Richard, yes you can set the tension in the springs of the RoadActive Suspension Kit part #RAS3611-Y low enough so that the suspension height is not raised at all. If you add in a lot more tension it will slightly affect the ride height like you…

view full answer...

Answer 10

Hey Rob, I went through the install instructions for the etrailer base plate kit part #e86YR that you referenced and did not find any mention of fit exclusions or special steps for if the truck has the air shudders/flaps that you mentioned so it…

view full answer...

Answer 11

Hey Jerry, we had a customer who came back with a Lariat like the one you're getting and told us it fit and worked great so it would work for yours. I attached a picture of it installed on a Lariat like yours for you to check out as well. What…

view full answer...

Answer 12

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Replacement Damper Lock Springs for Ventline Range Hood

Product Page this Question was Asked From

Continue Researching