Trailer Hitch Fit for 1993 Ford E-350 with 42 inch Frame

Question

Question:

I have a ford E350 with a 42inch frame width. Which hitch receivers will fit my frame?

asked by: Scott

0

Expert Reply:

Your 1993 Ford E-350 with a 42 inch frame has a standard dimension frame width so our Curt hitch part # 14053 would fit and work well. The other hitches listed at the attached link will also fit too.

expert reply by: Jameson C

0

Answer 1

It's not uncommon for hitches to get bent in shipping which makes the mounting holes not line up as easily as they should. So if the holes are off only by a little bit what you can do is start all of the bolts loose and then torque them down and…

view full answer...

Answer 2

The recommended solution for installing a hitch where the bolts all don't seem to perfectly line up is to first start each install bolt and leave it as loose as possible. This gives you a bit more leeway to compensate for holes that don't…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

Hey Kelly! The Curt 13146 fits 2016 - 2022 Honda Pilot. What you need for your 2026 Honda Pilot is the Curt #C22HR. This has a bolt-on installation and does not require any cutting or trimming of the bumper so you won't be modifying the vehicle.…

view full answer...

Answer 11

Hey Mike, so I checked with Curt and their hitch part number 13630 which is our part number #C33MJ does fit the 2025 Mazda CX-50 hybrid. Curt says this actually fits all models of the vehicle actually. What are you planning on using the hitch for?

view full answer...

Trailer Hitch Fit for 1993 Ford E-350 with 42 inch Frame

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching