Mounting Bracket for Tekonsha OEM Replacement Vehicle Wiring Harness on 2014 Toyota Highlander

Question

Question:

What size bracket will work with this 7-way plug? Some brackets are 2 inch diameter and others are 2-1/8 inch diameter.

asked by: Jason S

0

Expert Reply:

For the Tekonsha OEM Replacement Vehicle Wiring Harness # 22119 you need the 2 inch Pollak Mounting Bracket # PK12711U. You can see the dimensions of this bracket in the accompanying photo.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The particular parts you need to install a fully-functioning 7-Way on your 2019 Toyota Highlander Hybrid will depend on what exactly it's already equipped with. Either way you will need to start by adding a 4-Way connector harness. If your…

view full answer...

Answer 2

The trailer lighting circuits of the Tekonsha harness part #22119 that you referenced will be fully functional without having a brake controller installed. Brake controller circuits are totally independent from the light functions.

view full answer...

Answer 3

Since your 2020 Toyota Highlander has the factory towing package the correct trailer wiring kit is the part #22119 which will give you a 7-way harness. This kit (and any other option) does require the harness have the power wire ran from the rear to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller #C51180 you will need an almost fully functional 7 way connector; using something…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...