Is the MaxxAir Mini Trailer Roof Vent # MA00-03700 Plastic or Metal

Question

Question:

Thanks guys. Do you have this mini vent in black or any other colors besides white?

asked by: Bret C

0

Expert Reply:

The MaxxAir Mini Trailer Roof Vent # MA00-03700 that you referenced is made out of a durable plastic that actually does a really good job against the sun.

If you wanted a total metal vent then you could use the Ventline Ventadome Trailer Roof Vent # V2110SP-24 which is also a manually operated vent. The thing about this kit though is that it will keep out bugs and debris when left open but not rain. To keep it open while it is raining you would need to use a cover like the MaxxAir Standard RV and Trailer Roof Vent Cover # MA00-933066...which is made of plastic.

I recommend going with the Mini since plastic will also do a better job at resisting corrosion than the metal would.

expert reply by: Jon G

0

Bret C.

5/29/2018

Thanks guys. Do you have this mini vent in black or any other colors besides white?

Jon G.

5/29/2018

Yes we do! It is listed as part # MA00-03750 on our site.

Answer 1

To trim down the ceiling garnish of the MaxxAir Mini Trailer Roof Vent #MA00-03750 the easiest solution would be to measure how much you plan to cut off, mark where the cut needs to be made with a marker or pencil, and then use a hand saw to make the…

view full answer...

Answer 2

The insulators for standard 14x14 roof vents like part #CAM45192 do not fit into the vent opening of the MaxxAir Mini Roof Vent part #MA00-03700. The actual vent opening of the MaxxAir is 10-1/2" so the 14 inch insulator is not going to fit into…

view full answer...

Answer 3

The inner shroud of the vent is for looks only so it's very concerning that you're getting water through the cracks in it from overtightening the mounting screws. This would be an indication that you have a leak originating somewhere up on…

view full answer...

Answer 4

There isn't a standard non-powered MaxxAir RV vent to match the standard powered version so if you want to have matching vent lids then I recommend going the MaxxAir Mini and Mini Plus models: White: Non-Powered #MA00-03700 Powered #MA00-03801…

view full answer...

Answer 5

RV roof vents are typically all 14" x 14" and require a 14-1/4" x 14-1/4" hole to install. Manufacturers have started prepping enclosed trailers with frame work to support a vent installation but I can't confirm whether or not…

view full answer...

Answer 6

Hey Mike! The Soft Start Kit for Coleman-Mach RV Air Conditioners #CM56RR is designed to work with 45000, 47000, and 48000 air conditioners. Based on those numbers I'm assuming you those are 38000 series, but the model number doesn't always…

view full answer...

Answer 7

Hey Darin, this is a great question but since you have the Lippert Tire Linc Prep Kit that means you have everything but the sensors that mount on the valve stems and the repeater. So for that you'd just need the part #LC37VR which is a pair of…

view full answer...

Answer 8

Hey Al, Since your Dexter #9919860 is a 3,500lb axle you'll need grease seals #RG06-050 which come as a pair. I'd get 3 pairs (6 seals) that way you have an extra incase one goes in funky and bends (I've repacked hundreds of hubs and it…

view full answer...

Answer 9

Hello again Tony; you were probably looking at the conversion kit for the old Furrion Chill HE. There are no conversion kits for the new R32 systems, which is everything that has been released since last year. All versions of the Chill Cube will…

view full answer...

Answer 10

It is not an exact science that must be followed, so no worries. The amount of overhang can vary to a degree and still be just fine. Sometimes there will be an obstacle in play that determines limitations as well, adjoining slides so limited mounting…

view full answer...

Answer 11

Hey Bill, great question! The Signature Mach 15 is your standard AC unit which is probably what you want. The Roughneck has a fortified interior making it ideal for off-road and heavy industrial vehicle applications. Basically it is made to take more…

view full answer...

Answer 12

Hey Kim, The thickness of the LaSalle Bristol XTRM PVC Membrane in the #344270KIT21 kit is 27 mils, or 0.027" thick. The membrane itself has a 15 year warranty that is handled by LaSalle Bristol directly! What kind of trailer are you wanting to…

view full answer...

Is the MaxxAir Mini Trailer Roof Vent # MA00-03700 Plastic or Metal

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching