Determining The Correct Roof Vent For A Gladiator Cargo Trailer

Question

Question:

We are just replacing the one already there as it has a crack in it. Not motorized just a hand crank

asked by: Georgia M

0

Expert Reply:

RV roof vents are typically all 14" x 14" and require a 14-1/4" x 14-1/4" hole to install. Manufacturers have started prepping enclosed trailers with frame work to support a vent installation but I can't confirm whether or not your Gladiator Cargo Trailer will have this already.

If you don't already have frame work giving you a 14-1/4" x 14-1/4" space for the vent then you'll need to mark one out on the ceiling and cut into it and will most likely need build some frame work to support the vent or at least build a frame around the opening just to increase the thickness of the roof for the vent to be compatible.

To determine the correct vent for your needs you'll need to decide what features you want. There are standard vents with no fan like the Ventline E-Z Lift Ventadome Trailer Roof Vent # V3092-601-00 you were looking at.

There are vents with a standard design that have built in fans like the Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat - Powered Lift - 14-1/4" x 14-1/4" # FV803350.

There are also vents with a more unique lid design that allow you to use them in any weather and also while driving like the MaxxFan Deluxe Roof Vent w/ 12V Fan # MA00-06401K. I've attached a video of me installing this particular vent in another enclosed trailer below which can help further explain the steps for installing any vent on your trailer.

If you can give tell me what the intended purpose for the vent is and what features you'd like then I can find the correct vent for your needs.

expert reply by: Kevin C

0

Georgia

5/10/2022

We are just replacing the one already there as it has a crack in it. Not motorized just a hand crank

Kevin C.

5/10/2022

Since you're just replacing a standard vent with another standard vent I recommend the MaxxAir Mini Manual RV Roof Vent - Non-Powered - Black # MA00-03750 or # MA00-03700 for white. These vents can be used in any weather and allow you to vent your trailer while driving unlike all other models on the market.

Answer 1

When installing the MaxxFan Roof Vent #MA00A04301K that you referenced you will want to use butyl tape on the vent edges in addition to the sealant that you will apply around the unit to cover up bolt holes and any other areas that might lead to a…

view full answer...

Answer 2

Yes, you can but please keep in mind that this is not the most efficient way for charging a depleted battery. However, for maintaining a charge on a battery while you are driving you can use the 7-way connection such as the Optronics 7-way, #A7WCB…

view full answer...

Answer 3

To replace your Ventline V2094 trailer vent fan, use the following: - Ventline Ventadome Trailer Roof Vent w/ 12V Fan #V2094SP-30 This includes a garnish which fits roofs 1-7/8" to 3" thick, but if you have a roof with a different thickness…

view full answer...

Answer 4

The batteries should indeed be grounded to the trailer frame. A battery disconnect switch like #277-000096 would install inline on the positive circuit of the battery as shown in the video I've linked for you.

view full answer...

Answer 5

It really just depends on where you want it. I would say most have the vent in the living room area of the trailer but if you wanted one in the sleeping area you certainly could do that as well.

view full answer...

Answer 6

When installing marker lights we recommend using 18 gauge wire like #SWC97FR. This is stranded wire and is what we typically use when wiring marker lights like the #MCL32ABB for example. LED marker lights pull very low amperage so 18 gauge is likely…

view full answer...

Answer 7

The #38656 Junction Box won't take the place of a trailer mounted battery, but it provides a protected and organized method of connecting the wires from the trailer connector pigtail to all the various lighting, power and brake circuits on the…

view full answer...

Answer 8

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

Answer 9

The MaxxFan Deluxe, part #MA00-06401K, does come in white. Use part #MA00-05301K. There's also a 10-speed version with a thermostat in white; part #MA00-05100K

view full answer...

Answer 10

Yes, you can mount the Redline 2-Piece Roof Vent, #9139, on the front side of your cargo trailer. You will want to mount this vent with the vent slots facing down to prevent rain water or other elements from getting into the trailer. If you are…

view full answer...

Answer 11

Installation of the 2-Piece Polypropylene Trailer Vent, #HMAV2-AVT2, requires a 3 inch diameter hole when installed in a trailer with standard trailer wall thickness, 1-1/2 inches thick or less. This is the case for most enclosed trailers, but since…

view full answer...

Answer 12

While we have heard of people using electrical vents like the MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-06401K above a tub/shower, it is not meant to be installed in that location because water from the shower (whether it is from steam or from…

view full answer...

Determining The Correct Roof Vent For A Gladiator Cargo Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching