Can the Stromberg Carlson Electric Trailer Jack Be Rotated to Face a Different Direction

Question

Question:

How do you mount the strombeg carlson electric jack ... sideways. Looking to gain more room for vehicle lift gate to open. Thanks.

asked by: Cat

0

Expert Reply:

In order to position the Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift # JET-5000 can be rotated so that the switches are on the side and not facing forward. You will want to just simply rotate the jack until it lines up with the next set of bolt holes. This will be a 120 degree rotation.

expert reply by: Conner L

0

Answer 1

If your Husky Brute 4500 isn't extending or retracting properly then I recommend using the manual override to see if it's something internal or if it's an electronic part of the jack. For a replacement electrical part you'll need to…

view full answer...

Answer 2

The Stromberg Carlson Electric Trailer Jack #JET-5000 uses a 3 bolt mounting flange to attach to an A-frame trailer. If you wanted to rotate the jack on this flange you certainly could, but it would not be at a 90 degree angle since the mounting…

view full answer...

Answer 3

An electric a-frame tongue jack like the Lippert Electric Trailer Jack with Footplate part #LC285318 can indeed be rotated however, you would not be able to align the jack exactly 180 degrees as the mounting holes would not line up as you mentioned.…

view full answer...

Answer 4

Hey Jeffrey, thanks for reaching out! The etrailer Electric Trailer Jack #e55ZV does not require an additional fuse/relay as it has an auto-reset on built-in, and the outer diameter of the jack tube is 2-1/2". Are you looking to replace an older…

view full answer...

Answer 5

I have attached a drawing that shows how the wires are run on an electric jack like the Ultra-Fab Electric A-Frame Jack, part #UF38-944017.

view full answer...

Answer 6

It sounds like you need a little more space. While there isn't a way to turn the head on trailer jack #JET-5000 you might be able to turn the whole jack since it has slotted mounting holes. That is the first thing to try. If that isn't going…

view full answer...

Answer 7

Hello Bruce, yes it can. The etrailer Electric Trailer Jack #e55ZV can be rotated to the size and the bolts will still line up. We have this jack on one of our trailers here at the shop and I have checked and verified it can be rotated.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Mike, welcome back! Thanks for all of the info you listed from your Grand Design. Based on that and fact you have 5,200 lb axles the correct bearing kit would be the part #BK3-300 which comes with the correct bearings, races, seal, and a cotter…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can the Stromberg Carlson Electric Trailer Jack Be Rotated to Face a Different Direction

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching