How Many Threaded Ports on Demco Solenoid Kit DM5404

Question

Question:

How many threaded port are there on the solenoid

asked by: Jack W

1

Helpful Expert Reply:

Demco Solenoid Kit for Brake Actuators with Reverse Lockouts # DM5404 has a total of 3 threaded ports. One from the master cylinder to the solenoid, one from the side of the solenoid back to the master cylinder, and one at the back of the solenoid for the brake line.

expert reply by: Michael H

1

click to enlarge

Answer 1

I checked the instructions for the Demco Solenoid Kit #DM5404 and though it is a little vague, you will want to have the flared inlet attached to the actual brake line and the flat inlet attached to the #6 fitting (which then attaches to the master…

view full answer...

Answer 2

I spoke to my contact at Titan and he informed me that there really isn't a simple way to lock out the sliding portion of the Model 10 actuators. You would have to either weld the two portions of the actuator together or drill holes through them…

view full answer...

Answer 3

If the whole hitch (center section and brackets) are rusting you'd need to replace the entire setup with the part #BWGNRK1012. If it's just the mounting brackets you'd need the part #BWGNRM1012 or if it's just the center section part…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

How Many Threaded Ports on Demco Solenoid Kit DM5404

Product Page this Question was Asked From

Continue Researching