Will Replacement Amber Lens # A32AB Fit Side Marker Light # MCL32ABB

Question

Question:

This lens is described as a replacement for the MC32AB light, but will it also fit the LED version, MCL32ABB?

asked by: Al

0

Expert Reply:

Optronics does not list a replacement lens for marker light # MCL32ABB so the only option is to use # A32AB which will fit your light housing. The other option is to replace the whole light with a new one.

expert reply by: Michael H

0

Answer 1

Hey Scott, so the braking and hub components of a Dexter 3,500 lb axle made in 1999 would be the same as what's currently used so those components would transfer over. So a bare axle like the part #T3584F-EZ-8974 would work for you but you'd…

view full answer...

Answer 2

The brake mounting flanges, whether they be 4 or 5 bolt, have a standard hole spacing to fit their appropriate brake assembly. No worries about the brake assembly matching with the existing one on your axle. A 3500 lb axle like what you have will use…

view full answer...

Answer 3

Thanks for reaching out! It looks like your 1998 Coachmen Catalina 298FK travel trailer has tandem axles and is rated for 5,335 lbs so I would guess you have 3,500 lb axles. This means you'll want part #AKEBRK-35-SA for electric self-adjusting…

view full answer...

Answer 4

SAE-A-P2-83 is the lens rating, not a part number. A lens with SAE-A-P2-83 indicates that you have a Bargman 59 series light. The light has changed and the new replacement lenses will not fit the old style. You would have to replace the light,…

view full answer...

Answer 5

Hey Robert, thanks for the picture of your light assembly base. From seeing that I can tell the correct replacement lens would be the part #A32AB.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Will Replacement Amber Lens # A32AB Fit Side Marker Light # MCL32ABB

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching