Winch Stand Compatible with Sled Bed Snowmobile Trailer
Updated 12/26/2017 | Published 12/23/2017 >
Products Featured in This Question
Question:
I have a Sled Bed 2-place 10foot tilt snowmobile trailer. I want to mount a winch to pull a dead sled onto trailer. Would like to mount your CD31013G winch stand and Dutton-Lainson DL15337 Hand Winch. However, the center tongue beam on the trailer is 2inch X 3 3/4inch tall. The 2 cross beams are 3inch tall. If I mount the stand to one of the 2inch X 3inch angle beams Im concerned that it would not pull the sled at the proper angle. Do you have solution for my problem?
asked by: Doug T
Expert Reply:
The CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide # CE31013G should work on the center beam based on the measurements you gave. The additional height of the center beam won't be an issue as the width is still 2 inches. Because your trailer is 3-3/4 inches tall, this will required mounting directly to the frame instead of using u-bolts around the frame. You will also want to consider using the Dutton-Lainson Angle Mounting Plate for StrongArm Electric Winches # DL24059 to give you the proper winch angle.
You will not want to mount the stand off center as that angle would present an issue.
Product Page this Question was Asked From
CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide
- Boat Trailer Parts
- Winch Stand
- 30 Inch Tall
- Galvanized Steel
- CE Smith
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: winch stand
- Shop: CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide
- Video: Breaking Down the CE Smith Winch Stand
- Shop: CE Smith Keel Roller Assembly for 3" Wide Trailer Tongues - Galvanized Steel and Black Rubber
- Shop: CE Smith Spool Roller Assembly for Boat Trailers - Galvanized Steel and Black Rubber - 4"
- Video: Complete Breakdown of the CE Smith Keel Roller Assembly for 3" Wide Trailer Tongues
- Q&A: Picture of CE Smith Winch Stand # CE31013G Installed on Trailer
- Q&A: Are Additional Parts Needed for CE Smith Winch Stand
- Q&A: Will Trailer Tongue Hinge Kit Fit a 2" x 5" Trailer Tongue?
- Search Results: winch mount
- Shop: Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers
- Q&A: Availability of Vertical Winch Mounting Post
- Q&A: Size of Mounting Holes on Base of CE Smith Galvanized Winch Stand CE31013G
- Q&A: Parts Needed For A Spartan SB140 Boat Trailer
- Q&A: Winch Stand to Install Winch onto Boat Trailer
- Search Results: bearing kit
- Shop: Grease Seal - Double Lip - I.D. 1.249" / O.D. 1.983" - 2,000-lb to 2,200-lb Axles - Qty 1
- Shop: Dexter Oil Seal - Double Lip - I.D. 1.687" / O.D. 2.561" - 3.7K to 4.2K Axles - Qty 1
- Shop: Grease Seal - Double Lip - I.D. 1.688" / O.D. 2.332" - Older UFP Hubs/Marine Axles - Qty 1
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Search Results: trailer wiring
- Shop: Brake Controller



