Size of Mounting Holes on Base of CE Smith Galvanized Winch Stand CE31013G

Question

Question:

What is the size of mounting holes at the bottom of this winch mount?

asked by: Nima

1

Helpful Expert Reply:

The mounting holes on the bottom of the CE Smith Galvanized Winch Stand # CE31013G measure 7/16-inch. Please refer to the linked photo. This 30-inch tall winch stand is made of 12-gauge steel and is intended for 2-inch trailer tongues. It is USA-made.

expert reply by: Adam R

1

click to enlarge

Answer 1

I do have a solution for you but we don't offer any integrated winch and bow roller setups like the Knot Autoflex. Therefore, you'd have to purchase a winch stand assembly like the CE Smith Winch Stand part #CE31013G which bolts onto the…

view full answer...

Answer 2

I attached a picture that we recieved from a customer that shows the CE Smith winch mount #CE31013G installed and in use on a trailer for you to check out.

view full answer...

Answer 3

The CE Smith Winch Stand #CE31013G is basically the complete thing in and of itself. You just need to pick up appropriate hardware to install it to your trailer tongue and then install the actual winch on it and you'll be good to go. The mounting…

view full answer...

Answer 4

Hi Michael, While we don't have any way of knowing what winch stand goes on any specific trailer, it is possible we have an option for a winch stand for your Karavan trailer. The only option we have for a stand is the CE Smith Winch Stand…

view full answer...

Answer 5

To mount the CE Smith Winch Stand #CE31013G on a trailer requires you to slip the lower portion with the holes drilled through it over the pole tongue of your trailer. The various holes are there to allow you to match the correct height and angle…

view full answer...

Answer 6

I included a winch that will be very comparable to what comes on the CE Smith Multi Sport Plus Boat and Kayak Trailer #CE48870, but we do not have that exact model. I should also mention that there is no hardware included in this list, but everything…

view full answer...

Answer 7

The strap that you will need to use for the Dutton-Lainson Hand Winch #DL14125 is the 2" x 15' Strap #DL6148. The hook on this strap has a safety latch on it to help keep it secured to the load during operation. You will need a 2-3/4"…

view full answer...

Answer 8

Since the Malone EcoLight trailer part #MAL53FR has a tongue width of 2 inches you could use the tower kit part #CE31013G which is 30 inches tall as this is designed to fit 2 inch channels. Then you could use a winch like the Buyers Products part…

view full answer...

Answer 9

Since the Malone Microsport trailer part #MPG460G has a tongue width of 2 inches you could use the tower kit part #CE31013G which is 30 inches tall as this is designed to fit 2 inch channels. Then you could use a winch like the Buyers Products part…

view full answer...

Answer 10

In order to attach the CE Smith Winch Stand part #CE31013G to your boat trailer you would need to cut off the bottom portion of the stand and weld that directly to your trailer's tongue as it is only designed to bolt onto a 2" wide trailer…

view full answer...

Answer 11

Yes, you can add a winch to the Malone LowBed MicroSport Trailer item #MPG464-LB. You will want to use the CE Smith Winch Stand item #CE31013G. This will fit on the Malone trailer's 2" tongue. This stand is 30" tall and made of…

view full answer...

Answer 12

It sounds like you are looking for the CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide #CE31013G. This is designed for a 2 inch by 3 inch frame, so you will need to make some modifications. This is the only winch stand we…

view full answer...

Size of Mounting Holes on Base of CE Smith Galvanized Winch Stand CE31013G

Product Page this Question was Asked From

Continue Researching