2000 Toyota Tundra Compatibility with Draw-Tite Trailer Hitch Receiver # 37130

Question

Question:

If I have a bumper that is factory towable, does that mean I cannot use the 37130? Would I have to replace the bumper itself to make it work? The higher Class IV rating is the reason I prefer this to the 75105. The factory bumper has a Class II 2inch bottom receiver mount that I am removing regardless. Thanks.

asked by: James

0

Expert Reply:

I reached out to my contact at Draw-Tite and they believe the Draw-Tite Trailer Hitch Receiver - Multi Fit - Class IV - 2" # 37130 will fit your 2000 Toyota Tundra with the factory towable bumper, but they can't confirm it absolutely will fit. They don't have notes on the fit, but assume it may be an issue if there is a hitch ball installed on the bumper.

They can confirm the Class III # 75105 will fit. They also said since you are removing a factory hitch, it may change the installation as these are made for vehicles that do not have a factory hitch.

expert reply by: Jason S

0

Tom P.

1/11/2020

will hitch 37130 fit my 2005 Toyota tundra double cab and how much drilling

Jacob H.

1/15/2020

This hitch will fit your 2005 Toyota Tundra so long as your truck does not have a preexisting bumper hitch. There will be some drilling to get this hitch in place. You have to widen two holes and drill two new holes. But, if you would like to take a look at the installation instructions I have provided a link to our product page.

Helpful Links

Trailer-Hitch/Toyota/Tundra/2005/37130.html

Answer 1

Hey Dominick, thanks for reaching out! The Draw-Tite Max-Frame Trailer Hitch Receiver #75105 weighs 48-1/2 lbs. Just out of curiosity, what was your reasoning behind needing to know the weight?

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

2000 Toyota Tundra Compatibility with Draw-Tite Trailer Hitch Receiver # 37130

Featured Help Information

Miscellaneous Media

Continue Researching