Will the Curt Trailer Hitch Receiver # 13301 Work on 2011 GMC Sierra 1500

Question

Question:

Will this hitch fit a 2011 GMC Sierra 1500 reg cab?

asked by: Steve

0

Expert Reply:

Yes, I checked with Curt and this Curt Trailer Hitch Receiver, part # 13301, is a confirmed fit for your 2011 GMC Sierra 1500. I attached installation instructions for you to check out.

You may be interested in the following products to complete your towing setup:
Ball Mount 2-3/4 inch Rise or 4 inch Drop # 2753
Hitch Ball with 2 inch Diameter and Medium Shank # 19247
Tow Ready Custom Fit Vehicle Wiring # 118384 (instructions attached)

expert reply by: Jameson C

0

Answer 1

Hey Kerry, thanks for reaching out. The Curt #13301 is definitely what I recommend here. All of the hitches you mentioned, the Curt #C13061, #13322 and #13301 all fit the 2013 Silverado, but the #C13061 is only for the 2500 and 2500 models, so that…

view full answer...

Answer 2

Hey Byron, unfortunately the Curt Trailer Hitch #C14061 is not going to work with your 2013 Chevy Silverado 1500. Instead, you'd have to use the Curt Trailer Hitch Receiver #13301, which will fit your truck. If there is anything else I can do for…

view full answer...

Answer 3

The Curt #13322 Class III hitch uses a total of 6 bolts, two 1/2 inch carriage bolts and four M14 bolts. The 1/2 carriage bolts have a smooth round head on them, while the M14 bolts have a hex head on them so they can be tightened with a wrench.…

view full answer...

Answer 4

Yes, the Curt hitch part #13301 is a fit for your 2008 Chevy Silverado 1500.

view full answer...

Answer 5

Good question, and there is just a single difference between the Curt and etrailer trailer hitches that fit your 2010 Chevy Silverado 1500, which is the finish. The Curt has a glossier finish than the matte black finish of the etrailer hitch, so you…

view full answer...

Answer 6

You did not mention if your 2013 Chevy Silverado was a 1500, 2500, or 3500 so I can provide recommendations for all 3. For a 1500 I recommend Curt trailer hitch #14301. There is no drilling or trimming required for installation of this hitch. I have…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Will the Curt Trailer Hitch Receiver # 13301 Work on 2011 GMC Sierra 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching