Difference Between Curt & etrailer Trailer Hitch Receiver For 2010 Chevy Silverado 1500

Question

Question:

I have a 2010 Chevy Silverado w/t. I’m torn between the trailer hitch e98849 and the Curt 13322. What is the difference between the two. TY

asked by: Raymond F

0

Expert Reply:

Good question, and there is just a single difference between the Curt and etrailer trailer hitches that fit your 2010 Chevy Silverado 1500, which is the finish. The Curt has a glossier finish than the matte black finish of the etrailer hitch, so you can choose which you prefer:

- etrailer Trailer Hitch Receiver # e98849

- Curt Trailer Hitch Receiver # 13322

The matte black finish is nice as it hides the inevitable dings, scuffs and scratches better than the glossy finish, so that's the way I'd go, but if you don't feel strongly either way about the finish, then just go with the best price. Otherwise, these are the exact same hitch with the same 6,000 lb towing/600 lb tongue weight capacities and simple bolt-on installation.

expert reply by: Kyle S

0

Answer 1

The etrailer brand #e98849 is a fit for all trim levels of the 2008 Chevy Silverado 1500, including your LTZ. The hitch has a 6000 lb towing/600 lb tongue weight capacity or 10000 lb towing/1000 tongue weight if used with weight distribution. For a…

view full answer...

Answer 2

The etrailer brand #e98849 hitch which is a confirmed fit for your 2010 Silverado. The hitch installs using 6 bolts, two of which use nuts that are welded up into the holes closest to the rear of the frame as shown in the provided diagram. Two…

view full answer...

Answer 3

Both the Curt #C13382 and the etrailer #e98912 hitch are a 2" Class III hitch receiver that will provide a maximum gross trailer weight of 3,500 lbs and a maximum tongue weight of 525 lbs. You are correct, they are an identical hitch but our…

view full answer...

Answer 4

The difference between the Curt hitch part #13322 and the #13301 that you referenced is an aesthetic one mainly. The design of the #13301 is that the hitch tube is welded to the bottom of the cross tube which means that from the rear of the vehicle…

view full answer...

Answer 5

The distance from left to right on the Curt hitch part #13322 between the mounting holes on center is 35-5/8 inches and the distance from the mounting surface down to the top of the hitch opening is 5-1/2 inches.

view full answer...

Answer 6

Hey Byron, unfortunately the Curt Trailer Hitch #C14061 is not going to work with your 2013 Chevy Silverado 1500. Instead, you'd have to use the Curt Trailer Hitch Receiver #13301, which will fit your truck. If there is anything else I can do for…

view full answer...

Answer 7

Hey Craig, the Curt hitch part #13322 that you referenced is a confirmed fit for your 2011 and GMC Sierra 1500 and would work great to replace your OEM hitch. It may not use all of the same install hardware as your OEM hitch but it will be more than…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

We don't specify between the 1500 and 1500 HD in terms of fit in our guide, but I did check with our manufacturers for you to verify the fits for a trailer hitch receiver on your 2003 Chevy Silverado 1500 HD. The correct fit is going to depend on…

view full answer...

Answer 10

Hey Tom welcome back! The Single Axle Trailer Fender for Boat Trailers item #HP38VR does not include a backing plate, however I do have one for it. It's the Backing Plate for Single Axle Trailer Fender item #HP42FR. The Single Axle Trailer Fender…

view full answer...

Answer 11

Hi Lou! There is absolutely no problems installing the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs - Rear Axle #F2703 with an existing B&W Turnoverball gooseneck hitch in your 2012 Ford F-250. This kit was actually specifically…

view full answer...

Answer 12

There is a wiring kit for a brake controller Preston but it's not going to be a plug and play one. The 2025 Toyota Tacoma does not have a plug in brake controller port. Toyota stopped putting them in after the 2023 model. For your Tacoma, I…

view full answer...

Difference Between Curt & etrailer Trailer Hitch Receiver For 2010 Chevy Silverado 1500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching