Sizes of Available Equal-i-zer Weight Distribution Shanks
Updated 09/18/2017 | Published 09/16/2017
Products Featured in This Question
Question:
On the PART EQ90-02-4400 it has a 2-1/2 shaft for receiver . What size is then shaft on the Drop I need 2in X 2in and also what size are the holes I need 3/4in holes putting a eaz lift hatch on. Thanks
asked by: DALE M
Expert Reply:
The shanks included with most weight distribution systems, such as part # EQ90-02-4400, use standardized hole sizes and hole spacing for the vertical portion to which the weight distribution head assembly attaches. The other (horizontal) part of the shank that fits into the vehicle hitch receiver opening can be either 2 x 2-inches like part # EQ90-02-4400 that you referenced or 2-1/2- x 2-1/2-inches as with part # EQ90-02-4900.
The head portion of these systems all use the same mounting dimensions so if you were to change vehicles from one with a 2-inch hitch to one with a 2-1/2-inch hitch all you would need to do is replace the shank component. The rest of the system will still be usable on the new shank.
Product Page this Question was Asked From
Equal-i-zer Wt Distribution Shank - 12" - 13" Rise, 9" Drop - 600 to 1,400 lbs TW
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- 700 lbs TW
- 800 lbs TW
- 900 lbs TW
- 1000 lbs TW
- 1200 lbs TW
- 1300 lbs TW
- Fits 2 Inch Hitch
- Equal-i-zer
- Square - 9 Inch Drop
- Square - 13 Inch Rise
- Equal-i-zer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: weight distribution hitch shank
- Search Results: jack weld plate
- Search Results: hair pin
- Search Results: coupler pin
- Search Results: scissor jacks
- Search Results: clevis pin
- Shop: etrailer Scissor Stabilizer Jacks w/ Handle and Drill Adapter - 24" Lift - 10,000 lbs - Qty 4
- Q&A: How to Determine Correct Drop for Weight Distribution Shank
- Q&A: Footplate Recommendation to Replace Wheel Caster on Trailer Tongue Jack
- Search Results: stabilizer jacks trailer jack
- Video: A Closer Look at the Ark XO Drop Down Corner RV Stabilizer Jacks
- Video: The Low-Down on the Blue Ox TrackPro Weight Distribution Shank for 2" Hitches
- Video: Ultimate Overview of the Ultra-Fab Stackable Stabilizers for Small Trailers and Campers
- Video: In-Depth Review of the Coupler Pin
- Video: Review of TowSmart Hitch Pins and Clips - Standard Hitch Clip - TS37VR
- Video: Hands-On with the Equal-i-zer Wt Distribution Shank
- Video: Curt Coupler Safety Pin Feature Review
- Shop: etrailer Scissor Stabilizer Jacks w/ Handle and Drill Adapter - 24" Lift - 5,000 lbs - Qty 2
- Shop: Pivot Lock Hitch Pin - 5/8" Diameter - 2-5/8" Long
- Shop: Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - QTY 2
- Shop: Coupler Pin - 5/16" x 2-1/2"
- Shop: TowSmart Pivot Lock Hitch Pin - 5/8" Diameter
- Shop: Hitch Pin Clip for 5/8" Diameter Pins - 3-1/4" Long - Qty 1
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Install E-Track in 3 Easy Steps
- Q&A: Is Temp Sensor Still Located in Ceiling Plenum for Furrion Chill Cube AC Units?
- Q&A: Drop Shank Recommendation for Husky Weight Distribution for Ram Truck Towing Camper
- Q&A: Fastway e2 Weight Distribution for 2025 Ford F-150 Towing Enclosed Trailer
- Q&A: Where is the BulletProof Hitches Weight Distribution Shank BPH75RR Made?
- Q&A: Where to Install Transmission Cooler on a 2006 Toyota Sienna
on Accessories and Parts
