Solution for Broken Bulldog A-Frame Jack

Question

Question:

Found out the metal snapped. Solution?

asked by: Christopher W

0

Expert Reply:

Did you possible over extend the jack? If you let the jack over extend you will destroy the threads of the screw of the and nut which will prevent the jack from being able to go up or down.

expert reply by: Jameson C

0

Christopher

8/31/2017

Found out the metal snapped. Solution?

Jameson C.

8/31/2017

It would be time for a new jack as the part you broke is not replaceable. For a replacement, take a look at the Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black, Item # JET-5000.

Answer 1

Sounds like something loosened itself up after the first trip. I recommend lifting the cover and retightening the bolts on the Stromberg Carlson Electric Trailer Jack item #JET-5000. You'll want to check the mounting bolts too.

view full answer...

Answer 2

You can use the Replacement Manual Crank Handle for Stromberg Carlson Electric Trailer Jacks #SC94VR as a replacement crank for your Stromberg Carlson Electric Trailer Jack #JET-5000.

view full answer...

Answer 3

The Stromberg Carlson Electric Trailer Jack#JET-5000 that you referenced in your question has a distance of 23 inches from the mounting bracket to the top of the jack. You can measure this distance up from the A-frame of your trailer to see exactly…

view full answer...

Answer 4

Thanks for the picture of the a-frame jack mounting bolt hole dimensions you have. Based on that we know you have a standard jack mount on your trailer and the Stromberg Carlson Electric Trailer Jack #JET-5000 you are interested in is a confirmed fit…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Solution for Broken Bulldog A-Frame Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching