Replacement Hose Fitting for Firestone Ride-Rite Air Helper Springs # F2560

Question

Question:

Cani order another hose fitting for the top of the air bag,I damaged on when installing it?

asked by: Richard

1

Helpful Expert Reply:

Yes, we have both the Firestone Elbow Connector for 1/4" Tubing # F3031-1 and the Firestone Inflation Valve for 1/4" Tubing # F3032-1 should you need to replace that as well. Both of these fittings are used in the Firestone 2560.

expert reply by: Jon G

1

Answer 1

For your Air Spring Union Tee like #F3025-1 the only troubleshooting you can do is what you have already been doing. The Tee fittings simply use a compression so pushing into place is all that is required. The clean 90 degree cut is also all that is…

view full answer...

Answer 2

For the Firestone Ride Rite kit part #F2410 the correct elbow connector fitting is the part #F3031-1 which I confirmed with Firestone.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hi Fred! The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F24XV will indeed fit your 2025 Ram 2500 with the factory puck system. The only vehicles it won't fit are ones that have the factory…

view full answer...

Answer 10

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 11

Hey John, thanks for the picture of your truck bed! To install a set of 5th wheel rails in your 2022 Ram 2500, I recommend the B&W Custom Installation Kit w/ Base Rails item #BWRVK2602. This set of rails are industry standard so they'll work…

view full answer...

Answer 12

Hey Kim, thanks for reaching out. The Firestone Ride-Rite Air Bags with Easy Mount Compressor #F24XV do fit your 2020 Ram 2500 with rear coil springs, but the hang-up is the under-bed gooseneck hitch. On your truck, the air bag brackets and the…

view full answer...

Replacement Hose Fitting for Firestone Ride-Rite Air Helper Springs # F2560

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching