Replacement Threaded Hitch Pin for a Thule Vertex XT Bike Rack

Question

Question:

Dear, do you sell the hitch pin replacement for a thule vertex 9028xt? No the snug lock system, just the hitch pin such the same that came with the bike rack when new. Thanks

asked by: Alfredo

0

Expert Reply:

For your Thule Vertex XT you can use pin # TH62RE.

This is the pin part only from the Snug-Tite lock you mentioned. This will allow you to have a regular threaded pin and add the lock later if you wanted.

expert reply by: Michael H

0

Answer 1

The available trailer hitches for your 2019 Honda CR-V can be pretty easily categorized into hidden and non-hidden groups. I highly recommend going with a hidden-crosstube hitch, especially on a new vehicle like yours, as this is going to create a…

view full answer...

Answer 2

There are indeed two 2" trailer hitches available for your 2020 Honda CR-V; the etrailer #e98848 and the Curt #C13397. These Class III hitches are essentially identical in every way except for the finish/powder coat that they use. I personally…

view full answer...

Answer 3

For a hitch lock for the Thule 9028 rack that you have you'd need the hitch lock made specifically for the rack with the Thule Snug Tite part #THSTL2. The other locks will not fit since the rack you have has a threaded hitch pin design.

view full answer...

Answer 4

The correct replacement bolt to secure your Thule Vertex 2 Bike Rack TH9028XT to your hitch receiver is the Replacement 12 x 40 mm Hitch Bolt #908-1240-54. I confirmed this directly with Thule.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Replacement Threaded Hitch Pin for a Thule Vertex XT Bike Rack

Product Page this Question was Asked From

Continue Researching