Will SumoSpring SSR-610-47 Have a Gap Between Vehicle Frame When Unloaded

Question

Question:

What is the height of the Sumo Spring SS-610-47 for the Titan XD? The instructs show a height of 6 inches so the spring would be 2 5/8 inches away from the frame? This doesnt seem correct. My 2016 Titan Xd 2 WD has a height of 8 5/8 inches from leaf spring to frame

asked by: Dwane M

0

Expert Reply:

They are 6 inches tall. You do want a bit of distance between the SumoSpring and where it would contact the vehicle. This allows the ride quality to not be affected when the vehicle is unloaded. You don't want the SumoSpring # SSR-610-47 making contact all the time as that will give you a very bumpy ride quality.

expert reply by: Jameson C

0

Answer 1

Hey Austin, welcome back! I am doing well and hope you are too! The SumoSprings for your 2019 Mercedes-Benz Sprinter 2500 only come in the black 900 lbs capacity item #SSR-329-47. The only other SumoSpring options go higher item #SSR-327-40-2 and…

view full answer...

Answer 2

Hey Jeff, the correct SumoSprings kit for your 2017 Nissan Frontier is the part #SSR-612-47. Are you doing some towing?

view full answer...

Answer 3

No, It doesn't but I have a set that does. Since your 2025 Nissan Frontier has the king cab you'll need the SumoSprings Solo Custom Helper Springs item #SSR-612-47. These have a 1,800 lbs capacity and are specifically designed to fit the king…

view full answer...

Answer 4

We've checked with SumoSprings in the past with this question and they have told us that between 1/2 inch and 1 inch is standard clearance between the frame and the SumoSprings like the part #SSR-121-47 that you referenced.

view full answer...

Answer 5

Great question! I went ahead and reached out to my tech at SuperSprings (the makers of SumoSprings), and he confirmed that you cannot remove the spacer from the Solo Custom Springs #SSR-312-54 because you will not be able to tighten the bolts…

view full answer...

Answer 6

Hey Carl, with the SumoSprings Solo kits like the part #SSF-302-47 the minimum clearance between the spring and the vehicle axle is 1/2 inch. Normal clearance is between 1/2 inch and 1 inch.

view full answer...

Answer 7

It's going to vary some from vehicle to vehicle just because of how your truck rides. However, I reached out to SuperSprings and they told me that a half inch to an inch of clearance between the spring and the frame is fairly standard. The…

view full answer...

Answer 8

The easiest way to take tension off the round spring bars in your EAZ Lift Elite weight distribution hitch is to use the trailer tongue jack to raise the coupled trailer and hitch ball. By using the jack to support much of the tongue weight there…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Will SumoSpring SSR-610-47 Have a Gap Between Vehicle Frame When Unloaded

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching