Does Ball Mount Adapter part # BA-1 Fit Curt Weight Distribution Shank C17125

Question

Question:

Will the BA-1 fit C17125?

asked by: Dan

1

Helpful Expert Reply:

Yes, the Convert a Ball mount adapter # BA-1 is a fit for the weight distribution shank part # C17125. The adapter is designed to fit standard ball mount shanks like the Curt so it would be a great option.

expert reply by: Jameson C

1

Answer 1

The BulletProof Hitches replacement ball, part #358REPLACEMENTBALL, is designed specifically to fit BulletProof products. It may fit some others but not the Curt shank you're looking at. You can't see it in the picture on the page (There…

view full answer...

Answer 2

The Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches - 24" to 34" Long #C45048 is the best extension we carry for your need. However, it is limited to 6,000 lbs when extended 24 inches, so it will not work for your…

view full answer...

Answer 3

We have the Convert-a-Ball part #BA-1 which is a ball mount platform that fits standard weight distribution shanks like your Blue Ox SwayPro weight distribution. Then for a 2 inch hitch ball that would fit this you'd want the part #40038 or part…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hi Mike; we don't have a way to swap out the 2" ball on the Andersen Weight Distribution Hitch #AN88VR. We do have the 2-5/16" ball separately, #AN45VR, but we don't have it as a complete system. If you really want the Andersen,…

view full answer...

Answer 8

Welcome back Don! The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET is exactly what I would recommend using. This is a solid reliable system and the built in sway control will make a noticeable improvement in ride…

view full answer...

Answer 9

Hey Rex! Those are some great questions. A weight distribution hitch (WDH) isn't always needed but in your case you will want one. Typically if the weight of your trailer is more than 50% of the weight of your vehicle it is a good idea to use a…

view full answer...

Answer 10

Hey Michelle! There are definitely a lot of different weight distribution hitch (WDH) options out there. The most important thing is to make sure it is properly rated for the tongue weight of your setup. Looking at the specs for the 2022 Keystone…

view full answer...

Answer 11

Hey Jon, I have a solution for you but I would not recommend the Andersen Weight Distribution system part #AN33VR for your 2025 Brinkley Z Air 297. What we have found is that the Andersen system does a decent job with lighter weight trailers but for…

view full answer...

Answer 12

Hi James! With your GVWR being 7,600 pounds, your loaded tongue weight should be around 760 pounds. With that said, I recommend going with the Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 8.5K GTW, 850 lbs TW…

view full answer...

Does Ball Mount Adapter part # BA-1 Fit Curt Weight Distribution Shank C17125

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching