Recommended Trailer Hitch Receiver For 2017 Winnebago 2106DS

Question

Question:

Is there a bolt on solution

asked by: Aaron

0

Expert Reply:

For your 2017 Winnebago 2106DS, I recommend the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403. This is a weld on hitch to your Winnebago frame. It is adjustable from 47-1/8 to 77 inches and has a maximum tongue weight capacity of 350 lbs. It is powder coated for corrosion resistance. It will work great with a cargo carrier or RV rated bike rack with 2 inch receiver compatibility.

expert reply by: Jason S

0

Aaron

3/30/2017

Is there a bolt on solution

Jason S.

3/30/2017

There is a bolt on option that may work depending on the width of your frame. I recommend the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703. This hitch has a capacity of 350 lbs. The main hitch body can be trimmed so the ends are flush with the frame brackets. If you trim it, coat the bare metal with paint to protect against rust and corrosion. A support strap # 18050 is required with this hitch.

Answer 1

Yes, if you plan on bolting the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR on then you would need to drill holes in the adjustable arms in order to set them to the correct length. There aren't any predrilled so that this one…

view full answer...

Answer 2

Appreciate the photos, and we do have a hitch for you, but the Curt #13703 is for a max 72 inch wide frame measured outside to outside of the frame, and it looks like yours is 73 inches. So what you will need instead is a weld-on hitch that is…

view full answer...

Answer 3

I went out to our warehouse and measured the thickness of the L-Brackets on the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 and measured .34" or 11/32" thick. As per the second question, you are not going to be…

view full answer...

Answer 4

I spoke with Ultra-Fab and I have the dimensions of the weld-on tabs for the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames Item #UF35-946403 listed in the attached picture for you.

view full answer...

Answer 5

The street bikes you want to carry with the Swagman e-bike rack #S94FR would need to weigh less than 70 lbs for the rack to have the needed capacity. So assuming your bikes weighed each 70 lb plus the weight of the carrier which is 60 lb this would…

view full answer...

Answer 6

The distance from the two bolt holes on each side bracket for the Curt Adjustable Width Trailer Hitch Receiver #C13702 is right at 8-5/8" (center to center). I have also attached a diagram to assist. This adjustable hitch will fit frame widths…

view full answer...

Answer 7

I'd begin by contacting Forest River to ensure that the frame members at the rear of your fifth wheel have sufficient capacity to carry the weight of the carrier and the scooter without damaging anything. If Forest River gives you the go-ahead,…

view full answer...

Answer 8

I do have an option for you but as the frame has been modified, your only option would be a universal trailer hitch like the Adjustable Width Trailer Hitch Receiver for RVs part #C13702 which can be bolted or welded to the frame. It offers a class…

view full answer...

Answer 9

We highly recommend against double towing and many states either don't allow double (some states call it triple) towing or have numerous restrictions. Some states limit the total length of all 3 units, some only allow certain types of trailers…

view full answer...

Answer 10

To add a receiver hitch for a bike rack you'll actually connect the hitch to frame of your RV and not use the bumper as most aren't rated to hold the weight of a bike rack and bikes. You'll need to measure from beam to beam to see what…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Recommended Trailer Hitch Receiver For 2017 Winnebago 2106DS

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching